Sony MVS-7000X - Page 292

292
Applying Special Effects (Lighting and Recursive Effects)
Chapter 11 DME Operations
Point: Point light source. The position can be set.
Line: Line light source. The position and angle can be
set.
Whole: Non-directional light source which
illuminates the whole image (no settings).
5 According to the selected light source type, set the
following parameters.
When you selected Parallel
a) Minus moves counterclockwise, plus moves clockwise.
When you selected Point
•SD format
a) Minus moves left, plus moves right.
b) Minus moves down, plus moves up.
c) Minus moves forward, plus moves deeper.
•HD format
a) Minus moves left, plus moves right.
b) Minus moves down, plus moves up.
c) Minus moves forward, plus moves deeper.
When you selected Line
•SD format
a) Minus moves left, plus moves right.
b) Minus moves down, plus moves up.
c) Minus moves forward, plus moves deeper.
d) Minus moves counterclockwise, plus moves clockwise.
•HD format
a) Minus moves left, plus moves right.
b) Minus moves down, plus moves up.
c) Minus moves forward, plus moves deeper.
d) Minus moves counterclockwise, plus moves clockwise.
6 In the <Axis Select> group, select the coordinate space
in which to place the light source.
Source: Place the light source in the source coordinate
space. The spotlight moves when the image
moves.
Target: Place the light source in the target coordinate
space. The spotlight does not move, even when the
image moves.
For details of the coordinate space in which to place
the light source, see “Linking and unlinking image and
spotlight” (page 288).
To set a test sphere
1 In the Light 1 menu, press [Test Sphere], turning it on.
A test sphere effect appears on the surface of the
image.
2 Adjust the following parameter.
a) Light appears from Z direction. At –100.00 the light goes deepest, at
+100.00 the whole image is lit like a flat effect.
To select the lighted area
In the <Area Select> group, select one of the following.
FRGD: The light strikes the image foreground.
BKGD: The light strikes the image background.
Both: The light strikes both foreground and background.
For more information about the lighted area, see
“Selecting the lighted area” (page 288).
• If you select [Multiply] in the <Fill Blending Mode>
group of the Light Color Adjust menu (see page 294),
Knob Parameter Adjustment Setting values
1 Longitude Longitude –8.00 to +8.00
a)
2 Latitude Latitude –8.00 to +8.00
Knob Parameter Adjustment Setting values
1 X Movement in
X-axis direction
–6.00 to +6.00
a)
2 Y Movement in
Y-axis direction
–6.00 to +6.00
b)
3 Z Movement in
Z-axis direction
–6.00 to +6.00
c)
Knob Parameter Adjustment Setting values
1 X Movement in
X-axis direction
–24.00 to
+24.00
a)
2 Y Movement in
Y-axis direction
–24.00 to
+24.00
b)
3 Z Movement in
Z-axis direction
–24.00 to
+24.00
c)
Knob Parameter Adjustment Setting values
1 X Movement in
X-axis direction
–6.00 to +6.00
a)
2 Y Movement in
Y-axis direction
–6.00 to +6.00
b)
3 Z Movement in
Z-axis direction
–6.00 to +6.00
c)
4 Longitude Longitude –8.00 to +8.00
d)
Knob Parameter Adjustment Setting values
1 X Movement in
X-axis direction
–24.00 to
+24.00
a)
2 Y Movement in
Y-axis direction
–24.00 to
+24.00
b)
3 Z Movement in
Z-axis direction
–24.00 to
+24.00
c)
4 Longitude Longitude –8.00 to +8.00
d)
Knob Parameter Adjustment Setting values
5 Amp Distance of
light
–100.00 to +100.00
a)
Notes