EasyManua.ls Logo

Texecom Premier Elite Series

Texecom Premier Elite Series
152 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Premier Elite Series Installation Manual Engineer Utilities
INS176-15 129
Event Log Descriptions
Log Event
Description
### ARM FAILED
An exit fault from Zone ### has caused the system to fail to arm
### Flt Alarm
Zone ### has detected a Fault condition
### Mask Alarm
Zone ### has detected a Mask condition
### Test Failed
Manual or Periodical Test Call has failed on communication device ###
### Tested OK
Zone ### has activated during the walk test
#,# RESET AREAS -
Area have been reset using keypad #,# following an Intruder alarm
AC Off Alarm
The control panel has detected an AC Mains failure
ALARM ABORT
An Open After Alarm-Abort has occurred for area ?
ALARM Active
An Intruder alarm signal has been activated for area ?
Anti-Code Reset
A reset has been performed using the Anti-code reset procedure
AREA Armed
Area ? has been armed
AREA Disarmed
Area ? has been disarmed
ARMED WITH L/F
The system has been armed with a Line Fault condition present
ARMING FAILED
A Exit Error-Arm Fail has occurred on area ?
ARMING SUITE #
Area Arm Suite # was used to arm the system
ATS FAILED
The Communicator has failed to report to the Alarm Receiving Centre
ATS FLT Alarm
There is a problem with the telephone line
AUTO TEST CALL
An Automatic test call has been initiated
AUX #,# Tamper
An Auxiliary Tamper input from device #,# has been activated
AUX #,# Fault
An Auxiliary Fault input from device #,# has been activated
AV CLEARED by ##
The Audio Verification unit has been cleared down by user ##
BELL #,# Tamper
A Bell Tamper input from device #,# has been activated
BELL Active
The Bell output has been activated for area ?
BELL FUSE Alarm
The control panel Bell Fuse has failed
BOX LID Tamper
The control panel lid has been removed causing a Tamper alarm
CHARGER FAULT
Battery Charge Current has Failed
CIE Reset
The internal processor has failed its self checks.
CODE #,# Tamper
Too many invalid key presses have caused a tamper alarm from keypad #,#
Com??? Line Fault
The Com300, 2400 or ISDN has detected a line fault
COM PORT Alarm
A com port has generated an alarm
COM 3 Fault
Premier Elite 12.24.48 & 88 Com300/ 2400/ComPort + plugged on incorrectly or the port is programmed incorrectly.
CONFIRMED ALARM
Two or more detectors have activated, resulting in a confirmed alarm condition
CONFIRMED PA
Two or more PA zones have activated, resulting in a confirmed PA alarm condition
CONFIRMED INTRUDER
Two or more detectors have activated, resulting in a confirmed Intruder condition
CORRUPT EVENT
No event has been stored in memory
CROSS ### Alarm
A Verified Cross Zone (Beam Pair) Alarm has occurred from zone ###
DATA CHANGED
Programming data has been changed
DATE CHANGED
The control panel Time has been changed
DEFAULTS LOADED
The factory default values have been loaded into memory
DEFERRED
The arming mode was deferred for area ?
DOOR #,#
Door #,# has been opened by a user with Door Control
DOWNLOAD START
An Upload/Download has been initiated
DOWNLOAD END
The Upload/Download has finished
DURESS
User ## has entered a Duress Code at a keypad
Engineer Reset
A reset has been performed using an Engineers code
ENTRY Area ##
The Entry mode has been started for area ?
EXIT Area ##
The Exit mode has been started for area ?
EXP #,# Reset
A reset has been performed using the input on expander #,# (programmed as reset)
EXP #,# Line Fault
The Input on expander #,# (programmed as line fault) has been activated
EXP #,# LOST
Expander ## has been lost from the network
EXP #,# Tamper
The cover of expander #,# has been removed
EXP ## Low Voltage
Expander #,# has detected that its supply voltage is low
F_PA ##
A Panic Alarm from a Radio FOB has been generated
Fault Override
The system has been armed with a Fault condition present by a user
FIRE ### Active
Zone ### (programmed as Fire Alarm) has caused an alarm
FIRE ### Tamper
Zone ### (programmed as Fire Alarm) has caused an Tamper alarm
FIRST KNOCK ###
Zone ### (which is programmed as double knock) has activated for the first time
FUSE #,# Alarm
The Auxiliary 12V Fuse in device #,# has failed
GSM MODULE LOST
The GSM Module has lost communications with the control panel
iD Loop# Tamper
There is a short circuit on iD loop # on the iD expander
Key switch Reset
A reset has been performed using a key switch
KSW ### Disarmed
A Keyswitch zone type has been activated (zone number ###)
LOG ALERT
80% of the Event Log has filled (since the last Upload/Download)
LOG CLEARED
The event log has been erased
LOW BAT Alarm
The control panel has registered a low battery condition
LOW V #,# Alarm
Expander #,# has detected that’s its supply voltage is low
MANUAL TEST CALL
A Manual test call has been initiated
MIC ## TESTED
Microphone ## on the Audio Verification Module has been tested
Monitored Alarm
A zone programmed as key tube has caused an alarm
No RF Signal ###
The Wireless receiver has detected a signal loss from zone ###
PA From Remote FOB
A PA has been generated from a Remote Fob
Panel Line Fault
The control panel line fault input has been activated
PART Armed
Area ? has been Part Armed
PART 1 Armed
Part Arm 1 has been selected
PART 2 Armed
Part Arm 2 has been selected
PART 3 Armed
Part Arm 3 has been selected
Port Forwarding Success
The panel has opened the programmed port on the router
Port Forwarding Failed
The panel has not opened the programmed port on the router
POWERED UP
System Power Up (without doing a factory restart)
POWER O/P FAULT
The system has generated a Power Output Fault see Table Power ID Fault on Page 98
POWER UNIT FAILURE
The system has generated a rate of voltage failure
PROG. END
The Engineer has logged out of the Programming menu

Table of Contents

Other manuals for Texecom Premier Elite Series

Related product manuals