6
© 2008-2011 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO5520C/6520C/6530C
ERROR CODE and TROUBLESHOOTING
6 - 33
[E160] 4th drawer misfeeding (paper not reaching the 4th drawer feed sensor)
1. Open paper feed cover and check if there is any paper in front of the 4th drawer feed sensor.
Remove it if there is.
* If the error still occurs, check the following.
2. Is the 4th drawer feed sensor working? (Perform the input check: 03-[FAX]OFF/[8]/[D])
* If it is working properly, proceed to 7. If not, check 3 to 6 below.
3. Check if the connectors CN502 on the PFC board is disconnected from the 4th drawer feed
sensor or the harnesses are open circuited. Check if the connector CN502 on the PFC board is
disconnected. Correct if any.
4. Replace the 4th drawer feed sensor.
5. Replace the PFC board.
6. Is the 4th drawer feed clutch working? (Perform the output check: 03-122)
* If it is working properly, proceed to 10. If not, check 7 to 9 below.
7. Check if the connectors CN507 on the PFC board is disconnected from the 4th drawer feed
clutch or the harnesses are open circuited. Check if the connectors CN502 on the PFP board is
disconnected. Correct if any.
8. Replace the 4th drawer feed clutch.
9. Replace the PFC board.
10.Check the 4th drawer feed roller, separation roller and pickup roller. Replace them if they are
worn out.
[E180] Option LCF misfeeding (Paper not reaching the LCF feed sensor)
1. Is the LCF feed sensor working? (Perform the input check: 03-[SCAN]ON/[5]/[E]).
* If it is working properly, proceed to 7. If not, check 2 to 6 below.
2. Check if the connector CN503 on the PFC board is disconnected from the LCF feed sensor or
the harnesses are open circuited. Correct if so.
3. Check if the LCF feed sensor is correctly installed or the actuator is properly moved.
4. Replace the LCF feed sensor.
5. Replace the LCF board.
6. Replace the PFC board.
7. Is the LCF transport motor working? (Perform the output check: 03-127.)
* If it is working properly, proceed to 11. If not, check 8 to 10 below.
8. Check if the connector CN503 on the PFC board is disconnected from the LCF transport motor
or the harnesses are open circuited. Correct if so (including J854 and J850 on the LCF board).
9. Replace the LCF transport motor.
10.Replace the PFC board.
11.Check if there is any abnormality on the driving section of the LCF transport motor the roller.
Correct if any.
[E190] LCF misfeeding (paper not reaching the LCF feed sensor)
1. Open the LCF side cover and check if there is any paper in front of the LCF feed sensor. Remove
it if there is.
* If the error still occurs, check the following.
2. Is the LCF feed sensor working? (Perform the input check: 03-[SCAN]ON/[1]/[F])
* If it is working properly, proceed to 7. If not, check 3 to 6 below.
3. Check if the connectors CN349 on the LGC board is disconnected from the LCF feed sensor or
the harnesses are open circuited. Check if the connectors CN1 and CN6 on the LCF board are
disconnected. Correct if any.
4. Replace the LCF feed sensor.
5. Replace the LGC board.
6. Is the LCF feed clutch working? (Perform the output check: 03-250)
* If it is working properly, proceed to 12. If not, check 8 to 11 below.
7. Check if the connectors CN349 on the LGC board is disconnected from the LCF feed clutch or
the harnesses are open circuited. Check if the connectors CN1 and CN5 on the LCF board are
disconnected. Correct if any.
8. Replace the LCF feed clutch.
9. Replace the LGC board.
10.Check the LCF feed roller, separation roller and pickup roller. Replace them if they are worn out.
To Next Page
Loading...
