Toshiba Strata CTX28 - Page 342

Telephone Button Programming
100 Series Programs
13-18 Strata CTX Programming - Part 3: Telephone Button Programming 6/04
104-14 Emergency Call Timer
)% , n, +ROG +ROG
n = 10~180 sec.
(default = 30)
The Emergency Call timer sets a time (10 ~ 180 seconds) for
advancing the call to the next station in a list of destinations for the
call.
104-15 ABR Busy Detection
Time
)% , n, +ROG +ROG
n = 1~30 sec.
(default = 5)
The Destination Busy Detection timer sets the time (1 ~ 30 seconds)
to wait while looking for a busy condition on an external call. If
detected, it will trigger the initiation of the Automatic Busy Redial
cycle.
104-16 Lost Call Timer
)% , n, +ROG +ROG
n = 1~600 sec.
(default = 180)
The Lost Call timer sets the time (1 ~ 600 seconds) that a failed
transfer recall will ring on the originating station prior to attempting to
recall a secondary location.
104-17 Lost Call Final Timer
)% , n, +ROG +ROG
n = 1~600 sec.
(default = 180)
The Lost Call Final timer sets the time (1 ~ 600 seconds) that a failed
transfer recall will ring on the secondary location before being
automatically disconnected.
104-18 DTMF Tone Sending
Time
)% , n, +ROG +ROG
n = 1. 80 ms (default)
2. 160 ms
The DTMF tone sending duration (1-80 msecs, 2-160 msecs) for
dialing on CO Lines.
104-19 Auto Disconnect
)% , n, +ROG +ROG
n = 0~60 sec.
(default = 0)
Time after which an unsupervised trunk may be automatically
released.
104-23 System Timer
Network DSS Refresh
Timer
n = 20~180 sec. (default = 30) Select Network DSS Refresh Timer (20 -180 seconds). The time
interval when all Network DSS settings are refreshed system wide.
Note DSS button LEDs change state immediately when the status
of the DSS button changes - regardless of this timer value.
104-24 Outgoing Number
Display Timer
n = 1~120 sec. (default = 10) This timer sets how long dialed numbers will display on telephone
LCDs for outgoing line calls.
105
System Parameters
 , +ROG
This command assigns the system parameters.
105-01 Executive Override
)% , n, +ROG , +ROG
n = 1. Enable (default)
2. Disable
Break in warning tone of Executive Override Enable or Disable.
105-02 Station MOH
)% , n, +ROG , +ROG
n = 1. Quiet Tone
2. External 1 (default)
3. External 2
4. External 3
5. External 4
6. External 5
7. External 6
8. External 7
9. External 8
10. External 9
11. External 10
12. External 11
13. External 12
14. External 13
15. External 14
16. External 15
Music On Hold selection of Private Line and Station.
105-03 Ringing Transfer
)% , n, +ROG , +ROG
n = 1. RBT (default)
2. MOH
Tones for the transferred party after the ringing transfer takes place.
105-04 Transfer Privacy
)% , n, +ROG , +ROG
n = 1. Enable (default)
2. Disable
Transfer Privacy enabled: CO line buttons that have multiple
appearances will only flash and ring on the transferred-to telephone;
the same CO line button on other telephones will be red-busy.
Transfer Privacy Disabled: CO line buttons that have multiple
appearances will flash and ring on all telephones that have the CO
line button appearance.
105-05 Privacy Override
)% , n, +ROG , +ROG
n = 1. Enable
2. Disable (default)
Privacy Override Attendant Monitor warning Enable or Disable.
Table 13-5 Programs 103~107 (continued)
Button Sequence Value(s) Summary