Telephone Button Programming
300 Series Programs
Strata CTX Programming - Part 3: Telephone Button Programming 6/04 13-53
Telephone Button
Programming
300 Series Programs
Table 13-26 Programs 300~302
Button Sequence Value(s) Summary
300
Trunk Assignment
,
+ROG
This command assigns an analog or T1 trunk (line) and its
parameters to the system.
300-00 Line Number
n,
+ROG
n = 1~64 (CTX100)
1~96 (CTX670 Basic)
1~264 (CTX670 Exp.)
Enter the Line Number.
300-01 Line Equipment No.
)%
, xxyyzz,
+ROG
xx = Cabinet 1 (CTX100),
01~02 (CTX670 Basic),
01~07 (CTX670 Exp.)
Enter the line equipment number as xxyyzz. Equipment numbers are
required when assigning a new trunk to the system. It can also be
used to display the equipment location of existing trunks.
Example: If the trunk should be connected to an RCOU in cabinet
shelf 5, slot 2, circuit 3, enter 050203.
Cabinet numbers:
• CTX100 – Select 01 for Base and Expansion cabinet.
• CTX670 – Select 01 for Base and 02~07 respectively for each
Expansion cabinet.
Slot numbers:
• CTX100 – Select 01~04 for Base slots and 05~08 for Expansion
slots.
• CTX670 – Select 01~08 for Base slots and 01~10 for Expansion
slots.
yy = Slot 01~8 (CTX100),
01~10 (CTX670)
zz = Circuit (01~04)
...or zz = T1 Circuit 01~24
(CTX670).
300-02 Incoming Line Group
)%
, n,
+ROG
n = 0~32 (CTX100)
0~50 (CTX670 Basic)
0~128 (CTX670 Exp.)
(default = 0)
Assign the trunk to Incoming Line Group. Two-way trunks need to be
members of one incoming and one outgoing line group.
300-03 Outgoing Line Group
)%
, n,
+ROG
n = 0~32 (CTX100)
0~50 (CTX670 Basic)
0~128 (CTX670 Exp.)
(default = 0)
Assign the trunk to Outgoing Line Group. Two-way trunks need to be
members of one incoming and one outgoing line group.
300-04 Dial Mode
)%
, n,
+ROG
n = 1. Rotary Dial 10PPS
2. Rotary Dial 20PPS
3. DTMF (default)
Enter the Dial Mode.
• DP 10 PPS = Rotary Dial, 10 PPS
• DP 20 PPS = Rotary Dial, 20 PPS
300-05 Signaling
)%
, n,
+ROG
n = 1. DID
2. Loop (default)
3. Ground
4. Tie
5. LP (Japan)
6. SR (Japan)
7. ACU (UK)
Enter the signalling type.
300-06 Start Method
)%
, n,
+ROG
n = 1. Immediate Start
(default)
2. Timing Start
3. Wink Start
Enter the Start Method. This setting defines the start protocol method
used between the PSTN and this trunk. For DID/Tie trunks.
300-07 Release Supervision
)%
, n,
+ROG
n = 1. Received
2. Not Received (default)
Enable Release Supervision from the CO.
300-08 Answer Supervision
)%
, n,
+ROG
n = 1. Received
2. Not Received (default)
Enable Answer Supervision from the CO.
300-09 Trunk Name n = Up to 14 digits Enter the trunk name.
Note This function is accessible only through CTX WinAdmin.
300-10 External Ring Repeat
)%
, n,
+ROG
n = 1. Supplied (default)
2. Not Supplied
Supply the External Ringing Signal pattern to stations. For behind
PBX/Centrex trunks.
To Next Page
Loading...
