Need help?Do you have a question about the Unipulse F325 and is the answer not in the manual?
General| Brand | Unipulse |
|---|---|
| Model | F325 |
| Category | Measuring Instruments |
| Language | English |
Important safety warnings and cautions for using the F325 indicator.
Details critical warnings regarding installation, wiring, and operation to prevent severe injury.
Details cautions for safe installation, wiring, and operation to prevent injury or damage.
Lists items included in the product package for initial verification.
Diagram showing how the F325 connects to various external devices.
Describes the display unit and setting keys on the front panel.
Details grounding, options space, and power terminals on the rear panel.
Explains terminal assignments for control and sensor signals.
Outlines the sequence for setting up and operating the F325.
Covers warnings and cautions for connecting the signal I/O terminal block.
Provides steps for mounting the F325 into a control panel.
Details the procedure for wiring the signal I/O terminal block.
Explains how to connect four-wire and six-wire strain gauge sensors.
Explains RS-485 connection for point-to-point and multi-point setups.
Explains PhotoMOS relay output connections (plus/minus common).
Details no-voltage contact input and DC-input types.
Describes connecting AC power terminals and precautions.
Covers warnings on shock, cable use, breakers, and rush currents.
Details connecting DC power terminals and precautions.
Explains installing a surge protector for DC specifications.
Shows the structure of setting modes and their parameters.
Details the step-by-step process for changing settings using the keys.
Explains actual load and equivalent input calibration types.
Provides the sequence of steps for performing actual load calibration.
Details the procedure for equivalent input calibration.
Explains how to release the calibration lock function.
Describes how to select the excitation voltage for sensors.
Describes the process of setting the zero point for sensors.
Explains how to set the calibration lock to prevent unintended changes.
How to select the display update rate per second.
How to set the analog low-pass filter to reduce noise.
How to set the moving average filter to stabilize indicated values.
How to change the rate of referring to sampled data.
How to set the digital low-pass filter for noise reduction.
Explains how to set parameters to detect stability of indicated values.
Details how to configure motion detect time and range.
Explains how to set zero tracking to automatically correct zero point drifts.
Explains how to set the indicated value to zero via key or external input.
How to subtract a setting value from the indicated value.
How to enable or disable the ZERO key operation.
How to select functions for OUT1 and OUT2 terminals.
Explains setting and output conditions for HI, LO, HH, and LL limits.
Specifies the comparison timing for HI/LO limits.
How to set the comparison timing mode for HI/LO limits.
Explains hysteresis for preventing chattering in comparison outputs.
Details how to set the hysteresis value.
How to set alarm limits and monitor abnormal conditions.
Explains how to detect if an indicated value is near zero.
How to select between peak hold and sample hold modes.
Explains the operation of peak hold when hold fix section is OFF.
Explains the operation of sample hold when hold fix section is OFF.
How to switch peak hold performance between digital and analog.
How to select whether to insert a fix section into hold motion.
How to change when the hold value display is renewed.
How to set detection wait for hold input to ignore chattering.
How to enable or disable the HOLD key operation.
How to perform automatic printing based on stability and hold.
How to enable automatic printing with optional value hold.
How to print hold values when hold is released.
How to lock settings to prevent changes by operational errors.
How to use a password to initialize memory to factory defaults.
Explains the self-check function for memory and display inspection.
Details the process to rewrite memory contents to factory defaults.
Displays status of I/O inputs and checks ON/OFF status of I/O outputs.
Displays status of BCD inputs and checks BCD outputs.
Checks data transmission for RS-232C and RS-485 interfaces.
Shows current interface and installed option types.
Displays the product version information.
Details communication parameters for RS-485 interface.
Explains RS-485 connection for point-to-point and multi-point setups.
How to set RS-485 interface parameters and slave address.
How to set communication modes (Command, Continuous, Printed, Modbus-RTU).
Describes commands for reading values and status in UNI-Format.
Defines the format for writing/reading settings via RS-232C.
Details formats for continuous data transmission via RS-232C.
Lists and explains Modbus function codes used for communication.
Categorizes and describes event log entries based on bit status.
Retrieves slave status and checks communication via diagnosis.
Lists addresses for coil data types, including Hold, Zero, Calibration commands.
Lists addresses for input status and holding registers.
Lists addresses for holding registers, including limits, settings, and options.
Explains the BCD data output interface for BCD code data.
Details the steps for assembling the BCD output connector.
How to set the update rate for BCD data.
How to set the BCD output mode (linked/unlinked).
How to select functions for the B9 terminal.
Explains output/input signals and specifications for sink type BCD output.
Lists pin assignments for the BCD output connector.
Explains output/input signals and specifications for source type BCD output.
Lists pin assignments for the BCD output connector (BSC).
Explains the voltage output D/A converter and its specifications.
How to set zero and gain for D/A voltage output.
Explains the current output D/A converter and its specifications.
How to set zero and gain for D/A current output.
How to set the zero and full scale values for D/A conversion.
How to set the output mode for D/A conversion (linked/unlinked).
Details communication parameters for RS-232C interface.
How to set RS-232C interface parameters like baud rate and parity.
How to set communication modes (Command, Continuous, Printed).
Details commands for reading values and status via RS-232C.
Defines the format for writing/reading settings via RS-232C.
Details formats for continuous data transmission via RS-232C.
Lists and explains messages displayed for over-scale conditions.
Lists and explains error messages related to calibration failures.
Lists and explains general error messages like CAL2E and CALSP.
Details sensor excitation, input range, calibration, and A/D converter specs.
Specifications for analog and moving average filters.
Specs for display unit and parameter setting modes.
Provides dimensions for the standard unit without options.
Provides dimensions when BCD output options are selected.
Provides dimensions when D/A converter options are selected.
Provides dimensions when RS-232C option is selected.
Shows the internal architecture and component connections of the F325.
Lists parameters, defaults, ranges, and lock options for Setting Mode 1.
Lists parameters, defaults, ranges, and lock options for Setting Mode 2.
Lists parameters, defaults, ranges, and lock options for Setting Mode 3.
Lists parameters, defaults, ranges, and lock options for Setting Mode 4.
Lists parameters, defaults, ranges, and lock options for Setting Mode 5.
Lists parameters, defaults, ranges, and lock options for Setting Mode 6.
Lists parameters, defaults, and ranges for Setting Mode 7.
To Next Page
