Acre SPC42 - Page 253

To Next Page

To Previous Page

A Silent Alarm activation does not activate outputs 1–3 (no visual or audible indications of the

alarm). The alarm event is reported to the ARC. Silent alarms are only generated when alarm zones

with the Silent attribute have been opened when the system is set.

SPC42/52/53/63 – Installation & Configuration Manual Intruder alarm functionality

08.12.2023

Main Page

Default Chapter3
- Table of Contents3
1 Meaning of Symbols9
2 Security10
- Target Group10
- General Safety Instructions10
- Meaning of Written Warning Notices and Hazard Symbols12
  - Warning Notices12
  - Hazard Symbols12
3 Directives and Standards13
- EU Directives13
- Overview of Conformity to EN50131 Standard13
- Compliance with Vds 2115:2015-1218
  - Compliance with EN50131 Approvals18
- Compliance with en 50136-1:2012 and en 50136-2:201419
- Compliance with INCERT Approvals19
- Compliance with NF and A2P Approvals Including CYBER Requirements - SPC Products20
4 Technical Data21
- SPC Matrix21
5 Introduction22
6 Mounting System Equipment23
- Mounting a G2 Housing23
- Mounting a G3 Housing23
  - Mounting a Back Tamper Kit24
  - Battery Installation for EN50131 Compliance27
- Mounting a Keypad28
- Mounting an Expander28
- Wiring the X-BUS Interface28
  - Wiring the Inputs29
  - Wiring the Outputs30
7 Controller Hardware31
- Controller Hardware SPC42/SPC52/SPC53/SPC6331
8 Door Expander34
9 Wiring the System35
- Wiring the X-BUS Interface35
- Wiring of Branch Expander43
- Wiring the System Ground44
- Wiring the Relay Output44
- Wiring the Zone Inputs45
- Wiring an External SAB Bell48
- Wiring an Internal Sounder48
- Wiring Glassbreak49
- Installing Plug-In Modules49
10 Powering up the SPC Controller51
- Powering from Battery Only51
11 Keypad User Interface52
- Spck420/42152
12 Starting the System59
- Engineer Modes59
  - Engineer Pins59
- Programming with the Keypad59
- Configuring Start-Up Settings60
- Creating System Users61
- Programming the Portable PACE62
- Configuring Wireless Fob Devices63
  - Clearing Alerts Using the Fob63
13 Soft Engineer Programming Via the Keypad65
14 Engineer Programming Via the Keypad66
- System Status66
- Options67
- Timers71
- Areas75
- Area Groups77
- X-Bus77
  - X-BUS Addressing77
- XBUS Refresh77
- Reconfigure78
- Keypads/Expanders/Door Controllers78
- Addressing Mode87
- XBUS Type88
- Bus Retries88
- Comms Timer88
- Users88
  - Add88
  - Edit89
  - Delete91
- User Profiles92
  - Add92
  - Edit92
  - Delete92
- Wireless92
  - Select a Wireless Programming Option93
  - Two Way Wireless95
- Zones99
- Doors99
- Outputs103
  - Outputs Types and Output Ports104
- Communication108
  - Serial Ports108
  - Ethernet Ports108
  - Modems109
  - Central Station111
  - SPC Connect PRO113
- Test113
  - Bell Test113
  - Walk Test113
  - Zone Monitor114
  - Output Test115
  - Soak Test115
  - Audible Options115
  - Visual Indicators115
  - Seismic Test116
- Utilities116
- Isolate116
  - Event Log117
  - Access Log117
  - Alarm Log117
  - Change Engineer Pin118
  - Sms118
  - Set Date/Time120
  - Installer Text120
  - Door Control121
  - SPC Connect121
15 Engineer Programming Via the Browser122
- System Information122
- Ethernet Interface122
- Connecting to the Panel Via USB124
- Logging into the Browser124
- SPC Home125
- Panel Status127
- Logs137
- Users138
- Wireless149
  - Two Way Wireless150
- Configuration154
- Configuring Communications208
- File Operations244
  - File Upgrade Operations245
  - File Manager Operations247
16 Accessing Web Server Remotely249
- PSTN Connection249
17 Intruder Alarm Functionality251
- Financial Mode Operation251
- Commercial Mode Operation251
- Domestic Mode Operation252
- Full and Local Alarms252
18 System Examples and Scenarios254
- When to Use a Common Area254
19 Seismic Sensors256
- Seismic Sensor Testing256
20 Blocking Lock Operation260
- Blocking Lock260
- Authorized Setting of the Blocking Lock261
- Locking Element262
21 Appendix264
- Network Cable Connections264
- Controller Status Leds265
- Powering Expanders from the Auxiliary Power Terminals265
- Calculating the Battery Power Requirements266
- Domestic, Commercial and Financial Mode Default Settings267
- SIA Codes267
- CID Codes273
- User PIN Combinations275
- Duress Pins275
- Automatic Inhibits275
  - Zones275
  - Access Pins276
  - Engineer Access276
  - Keypad User Logoff276
- Wiring of Mains Cable to the Controller276
- Maintenance Controller276
- Maintenance277
- Zone Types278
- Zone Attributes283
- ATS Levels and Attenuation Specifications285
- Supported Card Readers and Card Formats286
- Flexc Glossary288
- Flexc Commands289
- ATS Category Timings292
- ATP Category Timings293
22 Notes295

Acre SPC42 - Page 253

Table of Contents