Acre SPC42 - Page 69

To Next Page

To Previous Page

ALARM ON EXIT ENABLED/DISABLED

Only available in ENGINEER CONFIG mode as setting is not in accordance with

EN50131.

LANGUAGE SYSTEM LANGUAGE

IDLE STATE :LANGUAGE

PIN DIGITS 4 DIGITS

5 DIGITS

6 DIGITS

7 DIGITS

8 DIGITS

CODED RESTORE ENABLED/DISABLED

WEB ACCESS ENABLED/DISABLED

Allows/restricts access to the web browser.

OPEN ZONES ENABLED/DISABLED

ALLOW

ENGINEER

ENABLED/DISABLED

ALLOW

MANUFACT.

ENABLED/DISABLED

SHOW STATE ENABLED/DISABLED

SPC42/52/53/63 – Installation & Configuration Manual Engineer programming via the keypad

08.12.2023

Main Page

Default Chapter3
- Table of Contents3
1 Meaning of Symbols9
2 Security10
- Target Group10
- General Safety Instructions10
- Meaning of Written Warning Notices and Hazard Symbols12
  - Warning Notices12
  - Hazard Symbols12
3 Directives and Standards13
- EU Directives13
- Overview of Conformity to EN50131 Standard13
- Compliance with Vds 2115:2015-1218
  - Compliance with EN50131 Approvals18
- Compliance with en 50136-1:2012 and en 50136-2:201419
- Compliance with INCERT Approvals19
- Compliance with NF and A2P Approvals Including CYBER Requirements - SPC Products20
4 Technical Data21
- SPC Matrix21
5 Introduction22
6 Mounting System Equipment23
- Mounting a G2 Housing23
- Mounting a G3 Housing23
  - Mounting a Back Tamper Kit24
  - Battery Installation for EN50131 Compliance27
- Mounting a Keypad28
- Mounting an Expander28
- Wiring the X-BUS Interface28
  - Wiring the Inputs29
  - Wiring the Outputs30
7 Controller Hardware31
- Controller Hardware SPC42/SPC52/SPC53/SPC6331
8 Door Expander34
9 Wiring the System35
- Wiring the X-BUS Interface35
- Wiring of Branch Expander43
- Wiring the System Ground44
- Wiring the Relay Output44
- Wiring the Zone Inputs45
- Wiring an External SAB Bell48
- Wiring an Internal Sounder48
- Wiring Glassbreak49
- Installing Plug-In Modules49
10 Powering up the SPC Controller51
- Powering from Battery Only51
11 Keypad User Interface52
- Spck420/42152
12 Starting the System59
- Engineer Modes59
  - Engineer Pins59
- Programming with the Keypad59
- Configuring Start-Up Settings60
- Creating System Users61
- Programming the Portable PACE62
- Configuring Wireless Fob Devices63
  - Clearing Alerts Using the Fob63
13 Soft Engineer Programming Via the Keypad65
14 Engineer Programming Via the Keypad66
- System Status66
- Options67
- Timers71
- Areas75
- Area Groups77
- X-Bus77
  - X-BUS Addressing77
- XBUS Refresh77
- Reconfigure78
- Keypads/Expanders/Door Controllers78
- Addressing Mode87
- XBUS Type88
- Bus Retries88
- Comms Timer88
- Users88
  - Add88
  - Edit89
  - Delete91
- User Profiles92
  - Add92
  - Edit92
  - Delete92
- Wireless92
  - Select a Wireless Programming Option93
  - Two Way Wireless95
- Zones99
- Doors99
- Outputs103
  - Outputs Types and Output Ports104
- Communication108
  - Serial Ports108
  - Ethernet Ports108
  - Modems109
  - Central Station111
  - SPC Connect PRO113
- Test113
  - Bell Test113
  - Walk Test113
  - Zone Monitor114
  - Output Test115
  - Soak Test115
  - Audible Options115
  - Visual Indicators115
  - Seismic Test116
- Utilities116
- Isolate116
  - Event Log117
  - Access Log117
  - Alarm Log117
  - Change Engineer Pin118
  - Sms118
  - Set Date/Time120
  - Installer Text120
  - Door Control121
  - SPC Connect121
15 Engineer Programming Via the Browser122
- System Information122
- Ethernet Interface122
- Connecting to the Panel Via USB124
- Logging into the Browser124
- SPC Home125
- Panel Status127
- Logs137
- Users138
- Wireless149
  - Two Way Wireless150
- Configuration154
- Configuring Communications208
- File Operations244
  - File Upgrade Operations245
  - File Manager Operations247
16 Accessing Web Server Remotely249
- PSTN Connection249
17 Intruder Alarm Functionality251
- Financial Mode Operation251
- Commercial Mode Operation251
- Domestic Mode Operation252
- Full and Local Alarms252
18 System Examples and Scenarios254
- When to Use a Common Area254
19 Seismic Sensors256
- Seismic Sensor Testing256
20 Blocking Lock Operation260
- Blocking Lock260
- Authorized Setting of the Blocking Lock261
- Locking Element262
21 Appendix264
- Network Cable Connections264
- Controller Status Leds265
- Powering Expanders from the Auxiliary Power Terminals265
- Calculating the Battery Power Requirements266
- Domestic, Commercial and Financial Mode Default Settings267
- SIA Codes267
- CID Codes273
- User PIN Combinations275
- Duress Pins275
- Automatic Inhibits275
  - Zones275
  - Access Pins276
  - Engineer Access276
  - Keypad User Logoff276
- Wiring of Mains Cable to the Controller276
- Maintenance Controller276
- Maintenance277
- Zone Types278
- Zone Attributes283
- ATS Levels and Attenuation Specifications285
- Supported Card Readers and Card Formats286
- Flexc Glossary288
- Flexc Commands289
- ATS Category Timings292
- ATP Category Timings293
22 Notes295

Acre SPC42 - Page 69

Table of Contents