To Next Page

To Previous Page

VLL Service Configuration Commands

Page 226 7210 SAS M Services Guide

bit-error-threshold

Syntax bit-error-threshold errors

no bit-error-threshold

Context config>service>epipe>sap>eth-cfm>mep>eth-test-enable

Description This command is used to specify the threshold value of bit errors.

one-way-delay-threshold

Syntax one-way-delay-threshold seconds

Context config>service>vpls>sap>eth-cfm>mep

Description This command enables/disables eth-test functionality on MEP.

Parameters seconds — Specifies the one way delay threshold in seconds.

Values 0-600

Default 3

Default Chapter3
- Table of Contents3
Preface15
- List of Technical Publications16
- Technical Support17
Getting Started19
- Alcatel-Lucent 7210 SAS Services Configuration Process19
- Table 1: Configuration Process19
- VLL Services19
- Getting Started20
- In this Chapter21
Services Overview23
- Introduction24
  - Service Types25
  - Service Policies26
- Alcatel-Lucent Service Model27
Services Overview28
- Service Entities28
Services Overview35
- Service Creation Process Overview62
- Figure 12: Service Creation and Implementation Flow62
- Deploying and Provisioning Services63
- Configuration Notes64
  - General64
- Configuring Global Service Entities with CLI65
  - Service Model Entities65
- Basic Configuration66
- Common Configuration Tasks68
  - Configuring Customers68
    - Customer Information68
  - Configuring an SDP71
    - SDP Configuration Tasks71
- Ethernet Connectivity Fault Management (ETH-CFM)74
- Service Management Tasks84
- Global Services Command Reference89
VLL Services119
- Circuit Emulation (Cpipe) Services120
  - Cpipe Service Overview120
  - Cpipe Service Modes120
- Ethernet Pipe (Epipe) Services136
- Support for Processing of Packets Received with more than 2 Tags on a Qinq SAP in Epipe Service (Only on 7210 SAS-M Network Mode)138
  - Feature Support, Configuration Notes and Restrictions139
- (Only on 7210 SAS-M Network Mode)140
Virtual Private LAN Service243
- VPLS Service Overview244
Virtual Private LAN Service245
- VPLS Features251
- BGP Auto-Discovery for LDP VPLS286
- Routed VPLS294
- Configuring a VPLS Service with CLI305
- Service Management Tasks351
- VPLS Services Command Reference357
- Table 17: Final Disposition of the Packet Based on Per FC and Per SAP Policer or Meter421
IEEE 802.1Ah Provider Backbone Bridging437
- IEEE 802.1Ah Provider Backbone Bridging (PBB) Overview438
IEEE 802.1Ah Provider Backbone Bridging439
- PBB Features439
- Configuration Examples454
  - PBB ELAN and ELINE454
  - MC-LAG Multihoming for Native PBB455
- PBB Command Reference457
  - PBB Show Commands465
Internet Enhanced Service499
Internet Enhanced Service500
- IES Service Overview500
- Figure 64: Internet Enhanced Service500
- IES Features501
  - IP Interfaces501
- Saps502
- Configuring an IES Service with CLI507
- IES Services Command Reference517
Virtual Private Routed Network Service549
Virtual Private Routed Network Service550
- VPRN Service Overview550
- VPRN Features557
Virtual Private Routed Network Service560
- CE to PE Routing Protocols563
  - PE to PE Tunneling Mechanisms563
  - Per VRF Route Limiting563
- Service Label Mode of a VPRN564
Internet Enhanced Service560
- Configuring a VPRN Service with CLI565
- VPRN Services Command Reference581
- Bgp Configuration Commands586
- Table 19: Final Disposition of the Packet Based on Per FC and Per SAP Policer or Meter624
- Pim Commands635
Show, Clear, Debug, Commands675
- Show Command Index675
Common CLI Command Descriptions939
- Common Service Commands940
Appendix: Split Horizon941
- Overview942
  - Topology942
  - Figure 69: Split Horizon Group Example942
- Configuration Guidelines943
  - Verification945
    - Standards and Protocol Support947
    - Standards Compliance947

Brand	Alcatel-Lucent
Model	7210 SAS M
Category	Switch
Language	English

Alcatel-Lucent 7210 SAS M Service Guide

Table of Contents

Other manuals for Alcatel-Lucent 7210 SAS M

Questions and Answers:

Alcatel-Lucent 7210 SAS M Specifications

Related product manuals