B&R Automation PC 620 - Page 241

Commissioning • Connection examples
Section 3
Commissioning
241Automation PC 620 with 945GME N270 CPU board User's Manual V 1.10
Cable lengths and resolutions for SDL transfer
The following table shows the relationship between segment lengths and the maximum
resolution according to the SDL cable used:
The cable types and resolutions shown with a footnote 1) in the previous table can only be
implemented starting with the following firmware and hardware versions:
Cables
Segment length [m]
Resolution
VGA
640 x 480
SVGA
800 x 600
XGA
1024 x 768
SXGA
1280 x 1024
UXGA
1600 x 1200
1.8
5CASDL.0018-00
5CASDL.0018-01
5CASDL.0018-03
5CASDL.0018-00
5CASDL.0018-01
5CASDL.0018-03
5CASDL.0018-00
5CASDL.0018-01
5CASDL.0018-03
5CASDL.0018-00
5CASDL.0018-01
5CASDL.0018-03
5CASDL.0018-00
5CASDL.0018-01
5CASDL.0018-03
5
5CASDL.0050-00
5CASDL.0050-01
5CASDL.0050-03
5CASDL.0050-00
5CASDL.0050-01
5CASDL.0050-03
5CASDL.0050-00
5CASDL.0050-01
5CASDL.0050-03
5CASDL.0050-00
5CASDL.0050-01
5CASDL.0050-03
5CASDL.0050-00
5CASDL.0050-01
5CASDL.0050-03
10
5CASDL.0100-00
5CASDL.0100-01
5CASDL.0100-03
5CASDL.0100-00
5CASDL.0100-01
5CASDL.0100-03
5CASDL.0100-00
5CASDL.0100-01
5CASDL.0100-03
5CASDL.0100-00
5CASDL.0100-01
5CASDL.0100-03
5CASDL.0100-00
1)
5CASDL.0100-01
1)
5CASDL.0100-03
1)
1) See table 151 "Requirements for SDL cable with automatic cable adjustment (equalizer)", on page 241
15
5CASDL.0150-00
5CASDL.0150-01
5CASDL.0150-03
5CASDL.0150-00
5CASDL.0150-01
5CASDL.0150-03
5CASDL.0150-00
5CASDL.0150-01
5CASDL.0150-03
5CASDL.0150-00
1)
5CASDL.0150-01
1)
5CASDL.0150-03
1)
-
-
-
20
5CASDL.0200-00
1)
5CASDL.0200-03
1)
5CASDL.0200-00
1)
5CASDL.0200-03
1)
5CASDL.0200-00
1)
5CASDL.0200-03
1)
5CASDL.0200-00
1)
5CASDL.0200-03
1)
-
-
25
5CASDL.0250-00
1)
5CASDL.0250-03
1)
5CASDL.0250-00
1)
5CASDL.0250-03
1)
5CASDL.0250-00
1)
5CASDL.0250-03
1)
-
-
-
-
30
5CASDL.0300-00
1)
5CASDL.0300-03
1)
5CASDL.0300-00
1)
5CASDL.0300-03
1)
5CASDL.0300-10
2)
5CASDL.0300-13
2)
2) See table 152 "Requirements for SDL cable with extender and automatic cable adjustment (equalizer)", on page 242
5CASDL.0300-10
2)
5CASDL.0300-13
2)
-
40
5CASDL.0400-10
2)
5CASDL.0400-13
2)
5CASDL.0400-10
2)
5CASDL.0400-13
2)
5CASDL.0400-10
2)
5CASDL.0400-13
2)
5CASDL.0400-10
2)
5CASDL.0400-13
2)
-
Table 150: Segment lengths, resolutions and SDL cables
Firmware Name Version Note
MTCX FPGA Firmware on the APC620 v 01.15 The version is read from BIOS - see the
BIOS description.
Supported starting with the APC620 /
PPC 700 Firmware upgrade (MTCX,
SDLR, SDLT) V01.10, available in the
download area of the B&R homepage.
MTCX PX32 Firmware on the APC620 v 01.55
SDLR FPGA Firmware on the AP Link SDL receiver and
transceiver
v 01.04
SDLT FPGA Firmware on the AP Link SDL transmitter v 00.02
Hardware Name Revision Note
5DLSDL.1000-00 AP Link SDL receiver Rev. B0
5DLSDL.1000-01 AP Link SDL transceiver Rev. B0
Table 151: Requirements for SDL cable with automatic cable adjustment (equalizer)