Danfoss VLT AQUA Drive FC 202

Other manuals for Danfoss VLT AQUA Drive FC 202

Service Guide370 pages

Programming Guide294 pages

Design Guide214 pages

Operating Instructions173 pages

Operating186 pages

Instruction Manual101 pages

Design Manual228 pages

Installation Manual124 pages

Installation Guide36 pages

Operating Manual162 pages

Installation Instructions6 pages

Questions and Answers:

M
Michele StewartAug 25, 2025
What to do if the motor is not running on a Danfoss Controller?
- D
  David EsparzaAug 25, 2025
  If your Danfoss Controller's motor isn't running, first ensure the motor is connected and check the service switch. If you're using a 24 V DC option card, make sure mains power is applied to run the unit. If the LCP is stopped, press [Auto On] or [Hand On], depending on the operation mode, to start the motor. Ensure a valid start signal is applied to initiate motor operation. If the motor coast signal is active, apply 24 V on terminal 27 or program this terminal to 'No operation'. Also, verify that the reference signal source is correctly programmed, checking settings in parameter group 3-1* References, wiring, scaling of terminals, and the reference signal itself.
J
Jerry FisherAug 31, 2025
What to do if I get Alarm 68, Safe Stop on my Danfoss Controller?
- J
  Jennifer HuntSep 1, 2025
  To resume normal operation of the Danfoss Controller after Alarm 68 (Safe Stop), apply 24 V DC to terminal 37 and then send a reset signal. This can be done via bus, digital I/O, or by pressing the Reset button.
A
Ashley HintonSep 1, 2025
What to do if Danfoss Controller issues an alarm when the frequency converter is tripped?
- B
  Brian RomeroSep 1, 2025
  If the Danfoss Controller issues an alarm because the frequency converter has tripped, you should remedy the fault condition. After doing so, reset the frequency converter, which will then be ready to restart operation.
S
stacy55Sep 2, 2025
Why Danfoss Controller issues a warning?
- N
  Nathan LamSep 2, 2025
  The Danfoss Controller issues a warning when an alarm condition is impending or when there is an abnormal operating condition. A warning clears by itself once the abnormal condition is resolved. It is recommended to investigate the cause as indicated in the alarm or warning.
C
Cynthia GallegosSep 2, 2025
How to resolve a trip-lock alarm on a Danfoss Controller?
- C
  cynthia10Sep 2, 2025
  To resolve a trip-lock alarm on a Danfoss Controller, remove input power to the frequency converter. Then, correct the cause of the fault and restore power.
J
James WalkerSep 3, 2025
What to do if Danfoss VLT AQUA Drive FC 202 DC Drives power off?
- H
  Haley WallaceSep 3, 2025
  If your Danfoss DC Drives show 'Power Off', it could be due to either no power supply or no link on the corresponding port. Ensure that the power is on and the link is active.
N
Nichole ThomasSep 3, 2025
Why Danfoss VLT AQUA Drive FC 202 power on with red light?
- J
  Jennifer StuartSep 4, 2025
  If your Danfoss DC Drives show 'Power On' and the indicator is red, this typically indicates an IP Address Conflict. Resolve the IP conflict.
K
kramirezSep 4, 2025
How to troubleshoot a dark or non-functional display on Danfoss VLT AQUA Drive FC 202 DC Drives?
- J
  Jessica OrtizSep 4, 2025
  If the Danfoss DC Drives display is dark or has no function, check the input power source. Also, check for any missing or open fuses, or a tripped circuit breaker. Ensure the LCP is receiving power, and if faulty, replace the LCP or connection cable. Verify that there are no shortcuts on the control voltage (terminal 12 or 50) or at the control terminals, and wire the terminals correctly. Use only LCP 101 (P/N 130B1124) or LCP 102 (P/N 130B1107). Adjust the contrast by pressing [Status] + [?]/[?]. If the display (LCP) is defective, replace it. For an internal voltage supply fault or defective SMPS, contact your supplier.
M
Maria WilsonSep 4, 2025
What to do if the Danfoss DC Drives display is intermittent?
- C
  Christopher LewisSep 5, 2025
  If the Danfoss DC Drives display is intermittent, it might be due to an overloaded power supply (SMPS) caused by improper control wiring or a fault within the frequency converter. If the display stays lit, check the control wiring for shorts or incorrect connections. If the display continues to cut out, follow the procedure for a dark display.
S
Steven JonesSep 5, 2025
Why Danfoss VLT AQUA Drive FC 202 DC Drives show DC Stop?
- S
  Shane OrtizSep 5, 2025
  The 'DC Stop' message on your Danfoss DC Drives indicates that the motor is being held with a DC current, determined by parameter 2-01 DC Brake Current, for a duration specified by 2-02 DC Braking Time. Alternatively, DC brake might be activated (2-03 DC Brake Cut In Speed [RPM]) when a stop command is active. It can also be activated via a digital input or serial communication.