■ mcast -- Show limits for ingress multicast traffic. (p. 569)
■ detailed -- Show Inbound Radius Override details. (p. 546)
■ port-list -- Specify ports for which information will be shown. ([ethernet] PORT-LIST) (p.
578)
■ show redundancy -- Display redundant information for Management and Fabric Modules (p. 585)
■ show rmon -- Show detailed rmon statistics for the ports (p. 586)
■ statistics -- Show RMON statistics for the ports ([ethernet] PORT-LIST) (p. 594)
■ show running-config -- Show the switch running configuration (p. 588)
■ status -- Check if the running configuration differs from the statup configuration. (p. 596)
■ show savepower -- Shows the user configured block power status (p. 589)
■ show services -- Show services information (p. 589)
■ services -- Show services information (SLOT-ID) (p. 589)
■ details -- (p. 547)
■ show sflow -- Display information regarding the configuration, sampling, and polling with respect
to 'sflow' (p. 590)
■ agent -- Displays read-only switch agent information: The agent address is normally the ip
address of the first vlan configured. (p. 529)
■ receiver-index < 1 to 3 > -- Select one of the three possible sFlow receiver tables. (NUMBER)
(p. 584)
■ destination -- Displays information about the receiver/collector/management-station to
which the sampling-polling data is sent. (p. 546)
■ sampling-polling -- Displays information about sampling and polling. (p. 589)
■ port-list -- Displays information about sampling and polling. ([ethernet] PORT-LIST) (p.
578)
■ show snmp-server -- Display information on all SNMP communities, trap receivers and Snmp
response/trap source-ip policy configured on the switch (p. 591)
■ community -- Specify SNMP community to which to restrict the output. (ASCII-STR) (p. 539)
■ traps -- Show all configured traps. (p. 599)
■ show snmpv3 -- Show configuration of SNMPv3 features. (p. 591)
■ access-rights -- Show information about access rights. (p. 527)
■ group < ManagerPriv | ManagerAuth | OperatorAuth | ... > -- Show SNMPv3 users. (p. 553)
■ sec-model -- Set security model. (p. 589)
■ ver1-2c < ver1 | ver2c > -- Configure SNMPv3 User entry. (p. 602)
■ ver3 -- SNMP version 3 security model. (p. 602)
■ ver3 < noauth | auth | priv > -- Set security level. (p. 602)
■ community -- Show SNMPv3 Community table. (p. 539)
■ COMMUNITY-NAME -- Show a specific community entry. (ASCII-STR) (p. 539)
■ enable -- Show SNMPv3 status. (p. 550)
■ engineid -- Show switch's SNMP engineId. (p. 550)
■ group -- Show SNMPv3 User to Group mappings. (p. 553)
■ group < ManagerPriv | ManagerAuth | OperatorAuth | ... > -- Show SNMPv3 users. (p. 553)
■ user -- Show a specific user. (ASCII-STR) (p. 601)
■ sec-model < ver1 | ver2c | ver3 > -- Show a specific security model. (p. 589)
■ notify -- Show SNMPv3 notification table. (p. 574)
■ NOTIFY-NAME -- Show a specific notification entry. (ASCII-STR) (p. 574)
■ only -- Show SNMP message reception policy. (p. 574)
■ params -- Show SNMPv3 Target Parameters table. (p. 575)
■ PARAM-NAME -- Show a specific Target Parameter entry. (ASCII-STR) (p. 575)
■ restricted-access -- Show SNMPv1 and SNMPv2c access properties. (p. 586)
■ targetaddress -- Show SNMPv3 Target Address table. (p. 597)
■ TARGETADDR-NAME -- Show a specifc target address entry. (ASCII-STR) (p. 597)
■ user -- Show SNMPv3 users. (p. 601)
■ USER-NAME -- Show a specific user. (ASCII-STR) (p. 602)
520© 2009 Hewlett-Packard Development Company, L.P.
showCommand Line Interface Reference Guide
To Next Page
Loading...
