Lenze i950 - Page 472

Address Designaon Default seng Data type Factor A M
0x28D4:002 SLP: Error
reacon: SLP2: Error reacon - (Read only) U8 -
0x28D4:003 SLP: Error reacon: SLP3: Error reacon - (Read only) U8 -
0x28D4:004 SLP: Error reacon: SLP4: Error reacon - (Read only) U8 -
0x28D5:001 SLP monitored: Output: SLP1 monitored: Output - (Read only) U8 -
0x28D5:002 SLP monitored: Output: SLP2 monitored: Output - (Read only) U8 -
0x28D5:003 SLP monitored: Output: SLP3 monitored: Output - (Read only) U8 -
0x28D5:004 SLP monitored: Output: SLP4 monitored: Output - (Read only) U8 -
0x28D8:001 SCA: Lower Poson limit: SCA1: Lower Poson limit - (Read only) I32 1 -
0x28D8:002 SCA: Lower Poson limit: SCA2: Lower Poson limit - (Read only) I32 1 -
0x28D8:003 SCA: Lower Poson limit: SCA3: Lower Poson limit - (Read only) I32 1 -
0x28D8:004 SCA: Lower Poson limit: SCA4: Lower Poson limit - (Read only) I32 1 -
0x28D9:001 SCA: Upper Poson limit: SCA1: Upper Poson limit - (Read only) I32 1 -
0x28D9:002 SCA: Upper Poson limit: SCA2: Upper Poson limit - (Read only) I32 1 -
0x28D9:003 SCA: Upper Poson limit: SCA3: Upper Poson limit - (Read only) I32 1 -
0x28D9:004 SCA: Upper Poson limit: SCA4: Upper Poson limit - (Read only) I32 1 -
0x28DA:001 SCA inbetween limits: Output: SCA1 inbetween lim-
its: Output
- (Read only) U8 -
0x28DA:002 SCA inbetween limits: Output: SCA2 inbetween lim-
its: Output
- (Read only) U8 -
0x28DA:003 SCA inbetween limits: Output: SCA3 inbetween lim-
its: Output
- (Read only) U8 -
0x28DA:004 SCA inbetween limits: Output: SCA4 inbetween lim-
its: Output
- (Read only) U8 -
0x28DC PDSS: Source SD-In - (Read only) U8 -
0x28DD PDSS: Source S bus - (Read only) U8 -
0x28DE:001 PDSS parameters: PDSS: Permanent acvaon - (Read only) U8 -
0x28DE:002 PDSS parameters: PDSS: Lower posion limit - (Read only) I32 1 -
0x28DE:003 PDSS parameters: PDSS: Upper
posion limit - (Read only) I32 1 -
0x28DE:004 PDSS parameters: PDSS: Lower SCS limit - (Read only) I32 1 -
0x28DE:005 PDSS parameters: PDSS: Upper SCS limit - (Read only) I32 1 -
0x28DE:006 PDSS parameters: PDSS: SCS from lower limit x rpm (Read only) U16 1 -
0x28DE:007 PDSS parameters: PDSS: SCS from upper limit x rpm (Read only) U16 1 -
0x28DE:008 PDSS parameters: PDSS: Max. speed x rpm (Read only) U16 1 -
0x28DE:009 PDSS parameters: PDSS: Max. delay - lower limit - (Read only) U16 1 -
0x28DE:010 PDSS parameters: PDSS: Max. delay - upper limit - (Read only) U16 1 -
0x28DE:011 PDSS parameters: PDSS: Error response - (Read only) U8 -
0x28DE:012 PDSS parameters: PDSS: Currently monitored speed x rpm (Read only) U16 1 X
0x28DE:013 PDSS parameters: PDSS: Min dierence monitored
speed
x rpm (Read only) I16 1 X
0x28DF PDSS: PDSSpos monitored output - (Read only) U8 -
0x28E0 PDSS: PDSSneg monitored output - (Read only) U8 -
0x28E8:001 Diagnosc values
conguraon: Diagnosc value 1
conguraon
PDSS [1] U16 X
0x28E8:002 Diagnosc values conguraon: Diagnosc value 2
conguraon
SS1, SS2 [2] U16 X
0x28E9:001 Diagnosc values: Diagnosc value 1 - (Read only) I16 1 X ●
0x28E9:002 Diagnosc values: Diagnosc value 2 - (Read only) I16 1 X ●
0x2900:001 Speed controller sengs: Gain 0.00033 Nm/rpm U32 100000 -
0x2900:002 Speed controller sengs: Reset me 17.6 ms U16 10 -
0x2900:003 Speed controller sengs: Rate me 0.00 ms U16 100 -
0x2901 Speed controller gain adapon 100.00 % U16 100 - ●
0x2902 I component load value 0.0 % I16 10 - ●
0x2903 Speed setpoint lter
me 0.0 ms U16 10 -
0x2904 Actual speed lter me 0.3 ms U16 10 -
0x2907:001 Addional speed limitaon 0 rpm U32 1 X ●
* Default seng depending on the size.
Appendix
P
arameter aribute list
472