Moor Instruments moorLDI2-VR - Page 4

MOOR INSTRUMENTS moorLDI2 RESEARCH USER MANUAL
iv
5.3 CHANGING SCAN PARAMETERS .................................................................................................................. 40
5.4 MOORLDI2-HR AND MOORLDI2-HIR SCAN DISTANCE AND SCAN SPEED ........................................... 40
6. MOORLDI2 SET UP .............................................................................................................................................. 41
6.1 INTRODUCTION ................................................................................................................................................ 41
6.2 MOOR LDI2 IMAGE SCAN CONFIGURATION ................................................................................................. 42
6.2.1 INTRODUCTION ....................................................................................................................................... 42
6.2.2 SPEED OF IMAGING ................................................................................................................................ 42
6.2.3 SIZE OF IMAGE ......................................................................................................................................... 42
6.3 SCANNER SET-UP ............................................................................................................................................. 42
6.3.1 IMAGE SCAN ............................................................................................................................................. 42
6.3.1.1 Scan Size, Area and Resolution .......................................................................................................................... 43
6.3.2 VIDEO AND DISTANCE ............................................................................................................................ 44
6.3.2.1 Mark Beam .......................................................................................................................................................... 45
6.3.2.2 Distance Measurement and CCD Size ................................................................................................................ 45
6.3.3 REPEAT AND LINE SCAN SETUP ............................................................................................................ 46
6.3.3.1 Repeat Scan Setup............................................................................................................................................... 46
6.3.3.2 Line Scan Setup .................................................................................................................................................. 47
6.3.4 GENERAL WINDOW OF SCANNER SETUP ............................................................................................... 47
6.3.4.1 Bandwidth ........................................................................................................................................................... 47
6.3.4.2 Normalisation ..................................................................................................................................................... 48
6.3.4.3 Background (BK) Threshold .............................................................................................................................. 48
6.3.4.4 Auto BK Set ........................................................................................................................................................ 48
6.3.4.5 Hood Mirror Option ........................................................................................................................................... 48
6.3.4.6 Gain Levels ......................................................................................................................................................... 48
6.3.4.7 Auto Gain ........................................................................................................................................................... 49
6.3.4.8 Reading (RU) ...................................................................................................................................................... 50
6.3.4.9 Scan ................................................................................................................................................................... 50
6.3.4.10 Abort ......................................................................................................................................................................... 50
6.3.4.11 Save Configuration .................................................................................................................................................... 50
6.3.5 SINGLE POINT MEASUREMENTS ............................................................................................................ 51
6.3.5.1 Single Point Setup ............................................................................................................................................... 51
6.3.5.2 Monitoring Duration .......................................................................................................................................... 51
6.4 S ETUP : P REFERENCE S ETUP .................................................................................................................................... 52
7. SINGLE IMAGE SCAN ......................................................................................................................................... 54
7.1 TO START ........................................................................................................................................................... 54
7.2 SAVING AN IMAGE SCAN ............................................................................................................................... 55
7.3 IMAGE DISPLAY IN MEASUREMENT MODE ............................................................................................... 55
8. REPEAT AND LINE SCAN MEASUREMENT .................................................................................................. 57
8.1 INTRODUCTION ................................................................................................................................................ 57
8.2 REPEAT AND LINE SCAN SET UP .................................................................................................................. 57
8.2.1 REPEAT INTERVAL ................................................................................................................................... 57
8.2.2 NUMBER OF SCANS ................................................................................................................................. 57
8.3 REPEAT SCAN START ...................................................................................................................................... 58
8.4 REPEAT SCAN DISPLAY DURING MEASUREMENT ................................................................................... 59
8.5 REPEAT LINE SCAN START ........................................................................................................................... 60
8.6 IONTOPHORESIS .......................................................................................................................................... 60
9. SINGLE POINT MEASUREMENT (SPM) ......................................................................................................... 61
9.1 INTRODUCTION ................................................................................................................................................ 61
9.2 POSITIONING OF BEAM FOR SPM ................................................................................................................. 61
9.3 BEAM MOVEMENT .......................................................................................................................................... 61
9.4 BEAM MOVEMENT RELATIVE TO PHOTO IMAGE .................................................................................... 61
9.5 SINGLE POINT MEASUREMENT WINDOW .................................................................................................. 61
9.6 DISTANCE - MOOR LDI2-TO-TISSUE ................................................................................................................ 62
9.7 SINGLE POINT CONFIGURATION .................................................................................................................. 62
9.8 AUTOGAIN ......................................................................................................................................................... 63
9.9 SINGLE POINT MEASUREMENT - START ..................................................................................................... 63
9.10 SINGLE POINT MEASUREMENT - FILE STORE ....................................................................................... 64