功能选择键和显示屏幕
FUNCTION SELECTION KEYS AND DISPLAY SCREENS
184
欧拉角指令 (MSX-711IV) 0 Euler Angle Command (MSX-711IV)
根据指导图和执行 G68.2 倾斜面加工指令的信息可输入各轴的
移动距离和旋转 / 倾斜角度。
The movement distance and rotation/tilting angle of each axis
can be input in reference to the guide diagram and message
for executing the G68.2 tilted working plane command.
1 有关 G68.2 的详细信息，参见单独手册“ 编程手册 ”。 1 For details on G68.2, refer to the separate volume
“ PROGRAMMING MANUAL ”.
1) 选择编辑模式或后台编辑模式。 1) Select the edit mode or the background edit mode.
2) 输入程序号，然后按下 [O- 号 . 搜索 ]。 2) Input the program number and press [O-No. SEARCH].
[ 显示程序 ] [The program is displayed]
3) 将光标移动至插入倾斜面加工指令的位置。 3) Move the cursor to the position where the tilted working
plane command is to be inserted.
[ 显示欧拉角指令窗口 ] [The euler angle command window is displayed]
4) 将光标移动到要输入数据的字段。 4) Move the cursor to the field for the data to be input.
[ 显示对应光标位置的项目的消息 ] [The message for the item is displayed]
5) 根据指导图读取信息然后输入数据。 5) Read the message and input the data in reference to the
guide diagram.
2 注意 2 NOTE
1. 最多可输入包括整数和小数在内的 8 位数。 1. Numbers of up to 8 digits including the integer and digits after
the decimal point can be input.
2. 按下 [ 取消 ] ，字段返回至输入前状态。 2. The fields are returned to the state before entry by pressing
[CANCEL].
5设定‘G49’/‘G53.1’为‘ON’，可省略手动输入。 5Manual input can be omitted by setting ‘ G49 ’/‘ G53.1 ’ to
‘ON’.
1 关于 G49 和 G53.1 的详情，参见单独手册“ 编程手册 ”。 1 For the details on G49 and G53.1, refer to the separate vol-
ume “ PROGRAMMING MANUAL ”.
6) 按下 [ 设定 ]。 6) Press [SET].
[ 输入数据进入缓冲区 ] [The input data is entered to the buffer]
5可在缓冲区中编辑输入数据。 5The input data can be edited in the buffer.
7) 按下
i
( 插入 ) 键。 7) Press the
i
(INSERT) key.
[ 在程序中插入缓冲区中的数据 ] [The data in the buffer is inserted into the program]
2 注意 2 NOTE
1. 按下 [ 返回 ] 关闭欧拉角指令窗口。 1. The euler angle command window is closed by pressing
[RETURN].
2. 切换屏幕后不保留倾斜面加工指令窗口。 2. The tilted working plane command window is not retained after
switching the screen.
前台编辑屏幕 Foreground Edit Screen
若要在屏幕上显示程序，输入程序编号并按下 [O- 号 . 搜索 ]。 To display a program on the screen, input the program number
and press [O-No. SEARCH].
2 注意 2 NOTE
在前台编辑操作期间，不可以同时显示两个程序。 During foreground editing operation, it is not possible to display two
programs.
< 软键功能 > <Soft-Key Functions>
[ 检查 /1/2 列 ] [CHECK/ 1/2-COL]
[ 扩展编辑 ] D [ 欧拉角指令 ]
[EXTENDED EDIT]D[EULER COMMAND]
模式选择按钮
f
[ 编辑 ] D 功能选择键
p
( 程序 )
Mode selection button
f
[EDIT] (Edit) D Function
selection key
p
(PROG)
To Next Page
Loading...
