mori seiki NMV5000 DCG - Emergency Stop;To Restart Machine; Turning off Power Supply; 关闭电源; 紧急停止; 重新启动机床

打开 / 关闭电源
TURNING ON/OFF POWER
64
1 “ 数控存储器 / 用户存储区中的程序输入 / 输出 ” （ 241 页） 1 “Program Input/Output in the NC Memory/User Memory Area”
(page 241)
7) 仔细阅读此小心信息，然后按下 [OK] 软键。 7) Read the caution message thoroughly, then press the [OK]
soft-key.
8) 拉出 [EMERGENCY STOP] ( 紧急停止 ) 按钮。 8) Pull out the [EMERGENCY STOP] (Emergency Stop)
button.
2 注意 2 NOTE
如果机床有多个 [EMERGENCY STOP] ( 紧急停止 ) 按钮，则务必
拉出所有按钮以解除紧急停止状态。
If the machine has more than one [EMERGENCY STOP]
(Emergency Stop) button, it is necessary to pull out all the buttons
to release the emergency stop state.
9) 再次按下数控电源按钮 [ 开 ]。 9) Press the NC power button [ON] again.
[ 重设紧急停止状态。EMG 显示消失。] [Emergency stop state is reset. EMG display disappears.]
10) 打开门，然后关上。 10) Open the door, then close the door.
[ 门被锁上。] [Door is locked.]
[ 状态指示灯准备完了点亮。] [Status indicator MRDY (machine ready) is illuminated.]
5此操作用于检查电路工作是否正常。 5This operation is for checking whether the electrical circuit
works normally.
11) 按下 [ 机内照明 ] 按钮。 11) Press the [Machine Light] button.
2 注意 2 NOTE
如果在主电源关闭时机床照明灯点亮，那么在电源重新打开时照明
灯将再次点亮。
If the machine light is ON when main power is turned OFF, the light
will be illuminated again when power is turned back on.
4-2 关闭电源
Turning OFF Power Supply
1) 按下 [EMERGENCY STOP] ( 紧急停止 ) 按钮。 1) Press the [EMERGENCY STOP] (Emergency Stop)
button.
[ 停止所有操作 ] [All operations stop]
2) 按下数控电源按钮 [ 关 ]。 2) Press the NC power button [OFF].
[ 数控电源被关闭。] [Power to the NC is turned OFF.]
3) 将主电源开关旋至 [OFF] 设定。
[ 机床电源被关闭。]
3) Turn the main power switch to the [OFF] setting.
[Power to the machine is turned OFF.]
4) 装备气动装置的机床，切断压缩空气气源。 4) On machines equipped with the pneumatic devices, shut off
the compressed air supply.
5) 关闭机床的车间侧主断路器。 5) Turn OFF the plant-side main circuit breaker for the
machine.
4-3 紧急停止 / 重新启动机床
Emergency Stop/To Restart Machine
若要在手动或自动运行期间停止机床操作，可用以下三种方法
之一：按下 [EMERGENCY STOP] ( 紧急停止 ) 按钮；
@
( 复
位 ) 键；自动运行按钮
w
[ 暂停 ]。根据使用方法的不同，机床
停止后的状态也将不同，务必了解各方法之间的差异。
To stop machine operation during manual or automatic
operation, use one of the following three methods: press the
[EMERGENCY STOP] (Emergency Stop) button; the
@
(RESET) key; the automatic operation button
w
[STOP]
(Stop). As the status of the machine after stopping will differ
depending on the method used, you must understand the
differences between the methods.