195
功能选择键和显示屏幕
FUNCTION SELECTION KEYS AND DISPLAY SCREENS
2) 按下 [ 改变文件夹 ] 选择数控程序列表屏幕 / 会话程序列表
屏幕。
2) Press [NC/CONV.] to select NC Program List screen/Dialog
Program List screen.
3) 在程序列表屏幕上将光标移动到所需程序。 3) On the program list screen, move the cursor to the desired
program.
4) 按下 [ 选择 ]。 4) Press [SELECT].
[ 显示‘ 缺少刀具列表 ’。] [‘ MISSING TOOL LIST ’ is displayed.]
2 注意 2 NOTE
如果所有的刀具已注册，则不显示‘ 缺少刀具列表 ’。 If all the tools are registered, ‘ MISSING TOOL LIST ’ is not
displayed.
5按下 [ 退出 ] 停止操作。 5To stop the operation, press [QUIT].
[ 显示信息‘ 执行中断 ’。] [The message ‘ Execution interruption ’ is displayed.]
5) 将光标移动到刀具应注册的刀座处，并按下
[
(Enter) 键 /
\
( 输入 ) 键。
5) Move the cursor to the pot where the tool should be
registered and press the
[
(Enter) key/
\
(INPUT) key.
[‘缺少刀具列表 ’的第一个刀具注册到光标所在的刀座编
号。]
[The first tool of ‘ MISSING TOOL LIST ’ is registered to the
cursor located pot number.]
6) 若要关闭显示未注册刀具列表的屏幕，按下 [ 返回 ] 软键。 6) To close the screen showing the list of unregistered tools,
press the [RETURN] soft-key.
若要返回‘ 程序列表 ’屏幕，按下 [O 参考 ] 软键。 To return to the ‘ PROGRAM LIST ’ screen, press the [O
REFER] soft-key.
指摘设置功能 0 Comment Setting Function
此功能用于从刀具文件列表中选择刀具类型，并在‘ 刀具注
册 ’屏幕上将其注册为已注册刀具的指摘。
This function is used to select a tool type from the tool file list
and register it as a comment for the registered tool on the
‘ TOOL REGISTRATION ’ screen.
当 MAPPS 参数 No. 1701 设置为“1”时，可用此功能。 This function can be used when MAPPS Parameter No. 1701
is set to “ 1 ”.
1) 按下 [>] 和 [ 设定注释 ] 显示刀具文件列表。
[ 刀具文件列表显示在‘ 刀具注册 ’屏幕上。]
1) Press [>] and [SET COMMENT] to display the tool file list.
[The tool file list is displayed on the ‘ TOOL
REGISTRATION ’ screen.]
2) 将光标移动到刀具应注册的刀座编号处。 2) Move the cursor to the pot number where the tool should be
registered.
若要将光标移动到刀座，按下 [ 到刀库 ]。然后按下 [ 到刀具
名称 ] ，将光标移动到刀具文件列表处。
To move the cursor to the magazine pot, press [TO
MAGAZINE]. And press [TO T. NAME] to move the cursor
to the tool file list.
[ 到刀库 ] 和 [ 到刀具名称 ] 软键交替显示。 The [TO MAGAZINE] and [TO T. NAME] soft-keys are
displayed alternately.
3) 将光标移动到刀具文件列表中所需的刀具处，并按下
[
(Enter) 键 /
\
( 输入 ) 键。
3) Move the cursor to the desired tool in the tool file list and
press the
[
(Enter) key/
\
(INPUT) key.
[ 所选择的刀具类型被设置为指摘（例如：‘ 钻头 ’）。] [The selected tool type is set as a comment (Example:
‘ DRILL’).
1.
按 [ 设定注释 ] 软键为每个刀具输入可长达 20 个字符的指摘。
但是，输入不超过 16 个指摘就可以在刀具偏移屏幕上显示每个
刀具。
1. Comments of up to 20 characters for each tool can be input by
pressing the [SET COMMENT] soft-key. However, input
comments of no more than 16 characters can be displayed for
each tool on the TOOL OFFSET screen.
2. 当 MAPPS 参数 No. 808 设置为“1”时，删除刀具编号将同时删
除其注册的刀具指摘数据。在默认设置下（ MAPPS 参数 No.
808 设置为“0”），如果曾经删除了刀具编号然后再次注册，则
恢复此刀具编号先前设置的刀具指摘数据。
2. When MAPPS parameter No. 808 is set to “ 1 ”, deleting a tool
number will also delete the tool comment data registered for the
tool number. With the default settings (MAPPS parameter No.
808 is set to “ 0 ”), if a tool number is deleted once and then
registered again, the tool comment data previously set for that
tool number will be retrieved.
3. 仅当 MAPPS 参数 No. 1701 设置为“1”时，可以删除指摘数据
（不涉及会话式刀具文件列表）。
3. Comment data can be deleted only when MAPPS parameter
No. 1701 is set to “ 1 ” (Not referring to the conversational tool
file list).
“T参考 ”功能 0 “ T REFER ” Function
此功能用于调用‘ 刀具注册 ’屏幕上的会话式刀具文件列表并选
择一个 T 代码设置作为刀具编号。
This function is used to call the conversational tool file list on
the ‘ TOOL REGISTRATION ’ screen and select a T code to be
set as a tool number.
To Next Page
Loading...
