Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
Basic
parameters
Running
the motor
Optimization
NV Media Card
Operation
Building
Automation
Advanced
parameters
Technical
data
Diagnostics
UL listing
information
120 HVAC Drive H300
Issue Number: 3
6 Basic parameters
6.1 Menu 0: Basic parameters
Parameter
Range Default
Type
OL RFC-A RFC-S OL RFC-A RFC-S
00.001
Motor Rpm {05.004} ±180000 rpm
RO Num ND NC PT FI
Speed Feedback {03.002}
VM_SPEED rpm RO Num ND NC PT FI
00.002 Output Frequency {05.001}
VM_SPEED_FREQ_
REF Hz
±2000.0 Hz
RO Num ND NC PT FI
00.003 Current Magnitude {04.001}
0.000 to VM_DRIVE_CURRENT_
UNIPOLAR A
RO Bit ND NC PT FI
00.004 Output Power (05.003) VM_POWER kW
RO Num ND NC PT FI
00.005 Software Version {11.029} 00.00.00.00 to 99.99.99.99
RO Num ND NC PT
00.010
Minimum Reference
Clamp
{01.007} VM_NEGATIVE_REF_CLAMP1 Hz / rpm 0.0 Hz / rpm RW Num US
00.011
Maximum Reference
Clamp
{01.006}
VM_POSITIVE_REF_CLAMP1
Hz / rpm
50 Hz default:
50.0 Hz
60 Hz default:
60.0 Hz
50 Hz
default:
1500.0
rpm
60 Hz
default:
1800.0
rpm
3000.0
rpm
RW Num US
00.012 Acceleration Rate 1 {02.011}
0.0 to
VM_ACCEL_RATE
s to Pr 01.006
0.000 to
VM_ACCEL_RATE
s to Pr 01.006
20.0 s
to Pr 01.006
20.000 s
to Pr 01.006
RW Num US
00.013 Deceleration Rate 1 {02.021}
0.0 to
VM_ACCEL_RATE
s from Pr 01.006
0.000 to
VM_ACCEL_RATE
s from Pr 01.006
20.0 s
from Pr 01.006
20.000 s
from Pr 01.006
RW Num US
00.014
Open-loop Control Mode {05.014}
Ur S (0), Ur (1),
Fixed (2),
Ur Auto (3),
Ur I (4),
Square (5),
Current 1P (6)
Ur I (4) RW Txt US
Speed Controller
Proportional Gain Kp1
{03.010} 0.0000 to 200.0000 s/rad 0.0300 s/rad RW Num US
00.015
Dynamic V to F Select {05.013}
Off (0) or
On (1)
On (1) RW Bit US
Speed Controller Integral
Feedback Gain Ki 1
{03.011}
0.00 to 655.35
s
2
/rad
0.10 s
2
/rad
RW Num US
00.016
Low Frequency Voltage
Boost
{05.015} 0.0 to 25.0 % 1.0 % RW Num US
Speed Controller
Differential Feedback
Gain Kd1
{03.012} 0.00000 to 0.65535 1/rad 0.00000 1/rad RW Num US
00.017 Number Of Motor Poles {05.011} Automatic (0) to 480 Poles (240) Automatic (0) 8 Poles (4) RW Num US
00.018 Rated Voltage {05.009} 0 to VM_AC_VOLTAGE_SET V
200V drive: 230V
50Hz default 400V drive: 400V
60Hz default 400V drive: 460V
575V drive: 575V
690V drive: 690V
RW Num RA US
00.019 Rated Speed {05.008} 0 to 33000 rpm 0.00 to 33000.00 rpm
50 Hz default -
1500 rpm
60 Hz default-
1800 rpm
50 Hz
default -
1450.00
rpm
60 Hz
default-
1750.00
rpm
3000.00
rpm
RW Num US
00.020 Rated Current {05.007} 0.000 to VM_RATED_CURRENT A
Maximum rated current
(Pr 11.060) A
RW Num RA US
00.021
Rated Frequency {05.006} 0.0 to 550.0 Hz
50Hz default: 50.0
60Hz default: 60.0
RW Num US
Volts per 1000 rpm {05.033}
0 to 10000 V
/ 1000 rpm
98 V /
1000 rpm
RW Num US
00.022
Maximum Switching
Frequency
{05.018}
2 kHz (0), 3 kHz (1), 4 kHz (2), 6 kHz (3), 8 kHz (4),
12 kHz (5), 16 kHz (6)
3 kHz (1) RW Txt RA US
00.023 Catch A Spinning Motor {06.009}
Disable (0), Enable (1),
Fwd Only (2), Rev Only (3)
Disable (0) RW Txt US
00.024 Auto-tune {05.012} 0 to 2 0 to 2 0, 1, 2, 6 0 RW Num NC
Menu 0 is used to bring together various commonly used parameters for basic easy set up of the drive. All the parameters in Menu 0 appear in other
menus in the drive (denoted by {…}). Menu 22 can be used to configure the parameters in Menu 0.
To Next Page
Loading...
