Schweitzer Engineering Laboratories SEL-787 - Page 10

viii List of Tables
SEL-787 Relay Instruction Manual Date Code 20081022
Table A.1 Firmware Revision History.................................................................................................... A.1
Table A.2 Instruction Manual Revision History.....................................................................................A.2
Table C.1 Supported Serial Command Sets ...........................................................................................C.1
Table C.2 Compressed ASCII Commands............................................................................................. C.2
Table C.3 SEL Communications Processors Protocol Interfaces .......................................................... C.4
Table C.4 SEL Communications Processor Port 1 Settings................................................................... C.7
Table C.5 SEL Communications Processor Data Collection Automessages ......................................... C.7
Table C.6 SEL Communications Processor Port 1 Automatic Messaging Settings .............................. C.8
Table C.7 SEL Communications Processor Port 1 Region Map............................................................ C.8
Table C.8 Communications Processor METER Region Map ................................................................ C.9
Table C.9 Communications Processor TARGET Region .................................................................... C.10
Table C.10 Communications Processor DEMAND Region Map .......................................................... C.11
Table D.1 DNP3 Implementation Levels ...............................................................................................D.1
Table D.2 Selected DNP3 Function Codes ............................................................................................D.3
Table D.3 DNP3 Access Methods..........................................................................................................D.4
Table D.4 TCP/UDP Selection Guidelines.............................................................................................D.6
Table D.5 DNP3 Access Methods..........................................................................................................D.6
Table D.6 SEL-787 Event Buffer Capacity ............................................................................................D.9
Table D.7 Port DNP3 Protocol Settings ............................................................................................... D.10
Table D.8 Serial Port DNP3 Modem Settings ...................................................................................... D.12
Table D.9 Sample Custom DNP3 AI Map ........................................................................................... D.15
Table D.10 SEL-787 DNP3 Device Profile............................................................................................D.19
Table D.11 SEL-787 DNP Object List ................................................................................................... D.20
Table D.12 DNP3 Reference Data Map .................................................................................................D.24
Table D.13 DNP3 Default Data Map ..................................................................................................... D.25
Table D.14 Example Object 12 Trip/Close or Code Selection Operation..............................................D.26
Table E.1 Modbus Query Fields ............................................................................................................ E.2
Table E.2 SEL-787 Modbus Function Codes......................................................................................... E.2
Table E.3 SEL-787 Modbus Exception Codes....................................................................................... E.3
Table E.4 01h Read Discrete Output Coil Status Command ................................................................. E.3
Table E.5 Responses to 01h Read Discrete Output Coil Query Errors.................................................. E.4
Table E.6 02h Read Input Status Command .......................................................................................... E.4
Table E.7 02h SEL-787 Inputs............................................................................................................... E.5
Table E.8 Responses to 02h Read Input Query Errors........................................................................... E.8
Table E.9 03h Read Holding Register Command .................................................................................. E.8
Table E.10 Responses to 03h Read Holding Register Query Errors........................................................ E.8
Table E.11 04h Read Input Register Command....................................................................................... E.9
Table E.12 Responses to 04h Read Input Register Query Errors ............................................................ E.9
Table E.13 05h Force Single Coil Command ..........................................................................................E.9
Table E.14 01h, 05h SEL-787 Output...................................................................................................... E.9
Table E.15 Responses to 05h Force Single Coil Query Errors .............................................................. E.12
Table E.16 06h Preset Single Register Command ................................................................................. E.12
Table E.17 Responses to 06h Preset Single Register Query Errors ....................................................... E.12
Table E.18 10h Preset Multiple Registers Command ............................................................................ E.12
Table E.19 10h Preset Multiple Registers Query Error Messages......................................................... E.13
Table E.20 60h Read Parameter Information Command ....................................................................... E.13
Table E.21 60h Read Parameter Descriptor Field Definition ................................................................ E.14
Table E.22 60h Read Parameter Conversion Field Definition ............................................................... E.14
Table E.23 Responses to 60h Read Parameter Information Query Errors............................................. E.14
Table E.24 61h Read Parameter Text Command ................................................................................... E.15
Table E.25 61h Read Parameter Text Query Error Messages ................................................................ E.15
Table E.26 62h Read Enumeration Text Command............................................................................... E.15
Table E.27 61h Read Parameter Enumeration Text Query Error Messages .......................................... E.16
Table E.28 7Dh Encapsulated Packet With Control Command............................................................. E.16
Table E.29 7Dh Encapsulated Packet Query Errors .............................................................................. E.16
Table E.30 7Eh NOP Command ............................................................................................................ E.17
Table E.31 Modbus Register Labels for Use With SET M Command .................................................. E.19
Table E.32 Modbus Register Map.......................................................................................................... E.22