viiList of Tables
Date Code 20081022 Instruction Manual SEL-787 Relay
Table 7.15 EVENT Command (Event Reports)..................................................................................... 7.20
Table 7.16 EVENT Command Format...................................................................................................7.20
Table 7.17 FILE Command.................................................................................................................... 7.20
Table 7.18 GOOSE Command Variants.................................................................................................7.21
Table 7.19 GROUP Command............................................................................................................... 7.22
Table 7.20 HELP Command .................................................................................................................. 7.23
Table 7.21 HISTORY Command ........................................................................................................... 7.23
Table 7.22 IDENTIFICATION Command............................................................................................. 7.23
Table 7.23 IRI Command ....................................................................................................................... 7.23
Table 7.24 LDP Commands ................................................................................................................... 7.24
Table 7.25 LDP Command Parameters .................................................................................................. 7.24
Table 7.26 L_D Command (Load Firmware) ........................................................................................ 7.25
Table 7.27 LOO Command .................................................................................................................... 7.25
Table 7.28 Meter Command................................................................................................................... 7.26
Table 7.29 Meter Command Parameters ................................................................................................ 7.26
Table 7.30 Meter Class........................................................................................................................... 7.26
Table 7.31 PASSWORD Command.......................................................................................................7.27
Table 7.32 PAS Command Format......................................................................................................... 7.27
Table 7.33 Factory Default Passwords for Access Levels 1 and 2......................................................... 7.27
Table 7.34 Valid Password Characters ................................................................................................... 7.28
Table 7.35 PUL OUTnnn Command ..................................................................................................... 7.29
Table 7.36 QUIT Command................................................................................................................... 7.29
Table 7.37 R_S Command (Restore Factory Defaults).......................................................................... 7.29
Table 7.38 SER Command (Sequential Events Recorder Report)......................................................... 7.29
Table 7.39 SER Command Format ........................................................................................................ 7.30
Table 7.40 SER D Command ................................................................................................................. 7.30
Table 7.41 SET Command (Change Settings) ....................................................................................... 7.30
Table 7.42 SET Command Format......................................................................................................... 7.31
Table 7.43 SET Command Editing Keystrokes...................................................................................... 7.31
Table 7.44 SHOW Command (Show/View Settings)............................................................................. 7.32
Table 7.45 SHOW Command Format ....................................................................................................7.32
Table 7.46 STATUS Command (Relay Self-Test Status)....................................................................... 7.34
Table 7.47 STATUS Command Report and Definitions ........................................................................ 7.34
Table 7.48 SUMMARY Command........................................................................................................7.36
Table 7.49 TARGET Command (Display Relay Word Bit Status) ........................................................ 7.36
Table 7.50 TARGET Command Format ................................................................................................ 7.36
Table 7.51 Front-Panel LEDs and the TAR 0 Command....................................................................... 7.36
Table 7.52 TIME Command (View/Change Time)................................................................................ 7.37
Table 7.53 TRIGGER Command (Trigger Event Report) ..................................................................... 7.38
Table 8.1 Front-Panel Automatic Messages........................................................................................... 8.3
Table 8.2 Front-Panel Pushbutton Functions ......................................................................................... 8.5
Table 8.3 Possible Warning Conditions (Flashing TRIP LED) ........................................................... 8.13
Table 8.4 SEL-787 Front-Panel Operator Control Functions .............................................................. 8.15
Table 9.1 Event Types ............................................................................................................................ 9.4
Table 9.2 Analog Event Report Columns Definitions............................................................................ 9.7
Table 9.3 Digital Event Report Column Definitions............................................................................ 9.14
Table 9.4 Differential Event Report Column Definitions for Analog Quantities ................................ 9.18
Table 9.5 Differential Event Report Digital Column Definitions for
Protection, Control and I/O Elements............................................................................... 9.19
Table 10.1 Resultant Scale Factors for Inputs........................................................................................ 10.2
Table 10.2 Serial Port Commands That Clear Relay Data Buffers ........................................................ 10.6
Table 10.3 CTR1 Phase Current Measuring Accuracy .......................................................................... 10.8
Table 10.4 CTR2 Phase Current Measuring Accuracy .......................................................................... 10.8
Table 10.5 Power Quantity Accuracy—Wye Voltages........................................................................... 10.9
Table 10.6 Power Quantity Accuracy—Delta Voltages ....................................................................... 10.10
Table 10.7 Periodic Relay Checks ....................................................................................................... 10.11
Table 10.8 Relay Self-Tests.................................................................................................................. 10.12
Table 10.9 Troubleshooting.................................................................................................................. 10.14
To Next Page
Loading...
