Schweitzer Engineering Laboratories SEL-787 - Page 8

vi List of Tables
SEL-787 Relay Instruction Manual Date Code 20081022
Table 4.40 Data Reset Setting ................................................................................................................4.92
Table 4.41 Setting Change Disable Setting ............................................................................................4.92
Table 4.42 Front-Panel Serial Port Settings............................................................................................4.93
Table 4.43 Ethernet Port Settings ........................................................................................................... 4.93
Table 4.44 Fiber-Optic Serial Port Settings............................................................................................4.94
Table 4.45 Rear-Panel Serial Port Settings.............................................................................................4.94
Table 4.46 Rear-Panel Serial Port (EIA-232/EIA-485) Settings ............................................................4.94
Table 4.47 Rear-Panel DeviceNet Port Settings .....................................................................................4.95
Table 4.48 Display Point and Local Bit Default Settings.......................................................................4.96
Table 4.49 Front-Panel General Settings ................................................................................................4.96
Table 4.50 LCD Display Point Settings .................................................................................................4.97
Table 4.51 Settings That Always, Never, or Conditionally Hide a Display Point..................................4.98
Table 4.52 Entries for the Four Strings...................................................................................................4.98
Table 4.53 Binary Entry in the Name String Only ...............................................................................4.100
Table 4.54 Analog Entry in the Name String Only .............................................................................. 4.101
Table 4.55 Entry in the Name String and the Alias Strings.................................................................. 4.101
Table 4.56 Example Settings and Displays ..........................................................................................4.102
Table 4.57 Target LED Settings............................................................................................................4.105
Table 4.58 Pushbutton LED Settings....................................................................................................4.106
Table 4.59 Auto-Removal Settings.......................................................................................................4.106
Table 4.60 SER Trigger Settings ..........................................................................................................4.107
Table 4.61 Enable Alias Settings..........................................................................................................4.107
Table 4.62 SET R SER Alias Settings ..................................................................................................4.108
Table 4.63 Event Report Settings .........................................................................................................4.108
Table 4.64 Load Profile Settings ..........................................................................................................4.108
Table 4.65 DNP Map Settings ..............................................................................................................4.109
Table 4.66 User Map Register Settings ................................................................................................4.110
Table 5.1 Measured Fundamental Meter Values ....................................................................................5.3
Table 5.2 Measured Differential Meter Values.......................................................................................5.4
Table 5.3 Thermal Meter Values ............................................................................................................ 5.5
Table 5.4 RTD Input Status Messages....................................................................................................5.5
Table 5.5 Maximum/Minimum Meter Values ........................................................................................5.6
Table 5.6 RMS Meter Values..................................................................................................................5.8
Table 5.7 Demand Values .......................................................................................................................5.9
Table 5.8 Measured Harmonic Meter Values .......................................................................................5.10
Table 5.9 Synchrophasor Measured Values..........................................................................................5.11
Table 5.10 Through-Fault Element Settings...........................................................................................5.14
Table 5.11 Through-Faults Events Report Messages .............................................................................5.17
Table 6.1 Methods of Accessing Settings...............................................................................................6.1
Table 6.2 SHOW Command Options .....................................................................................................6.4
Table 6.3 SET Command Options..........................................................................................................6.4
Table 6.4 SET Command Editing Keystrokes........................................................................................6.5
Table 6.5 SET Command Format ...........................................................................................................6.5
Table 6.6 Setting Interdependency Error Messages ............................................................................... 6.6
Table 7.1 SEL-787 Communications Port Interfaces .............................................................................7.1
Table 7.2 EIA-232/EIA-485 Serial Port Pin Functions .........................................................................7.5
Table 7.3 Protocols Supported on the Various Ports ..............................................................................7.7
Table 7.4 Serial Port Automatic Messages...........................................................................................7.11
Table 7.5 Command Response Header Definitions.............................................................................. 7.12
Table 7.6 Access Commands................................................................................................................7.13
Table 7.7 ANALOG Command............................................................................................................7.15
Table 7.8 ANALOG Command Format ............................................................................................... 7.15
Table 7.9 COM Command ...................................................................................................................7.17
Table 7.10 CONTROL Command..........................................................................................................7.18
Table 7.11 Three Remote Bit States .......................................................................................................7.18
Table 7.12 COPY Command .................................................................................................................. 7.18
Table 7.13 COUNTER Command..........................................................................................................7.18
Table 7.14 Date Command .....................................................................................................................7.19