EasyManuals Logo

Siemens SINUMERIK Commissioning Manual

Siemens SINUMERIK
736 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #204 background imageLoading...
Page #204 background image
Tool management
6.2 Settings in the configuration file
HMI Advanced (IM4)
198 Commissioning Manual, 03/2009, 6FC5397-0DP10-3BA0
; in the magazine list and in the tool list.
; Example: ToolState_Lang_12345678=12345678_ToolState_Lang
MagPlaceState_Lang_12345678=12345678_MagPlaceState_Lang
; use patm_*.ini
; The new magazine location status bits can be displayed in each
; list display. The parameters are set in the sections:
"[1_MagList]", "[2_MagList]", "[3_MagList]"
"[1_ToolList]", "[2_ToolList]", "[3_ToolList]"
"[1_ActList]", "[2_ActList]", "[3_ActList]"
; Entries are for example:
12=TC_MPP4_9, 1, TC_MPP4_9 ;PlaceStatus Left,
;Reserved in left half location
13=TC_MPP4_10, 1, TC_MPP4_10 ;PlaceStatus Right,
;Reserved in right half location
14=TC_MPP4_11, 1, TC_MPP4_11 ;PlaceStatus Top,
;Reserved in upper half location
15=TC_MPP4_12, 1, TC_MPP4_12 ;PlaceStatus Bottom,
;Reserved in lower half location
16=TC_MPP4_13, 1, TC_MPP4_13 ;PlaceStatus Bit 13 of 1 to 16
17=TC_MPP4_14, 1, TC_MPP4_14 ;PlaceStatus Bit 14 of 1 to 16
18=TC_MPP4_15, 1, TC_MPP4_15 ;PlaceStatus Bit 15 of 1 to 16
19=TC_MPP4_16, 1, TC_MPP4_16 ;PlaceStatus Bit 16 of 1 to 16
; Example: MagPlaceState_Lang_12345678=12345678_MagPlaceState_Lang
; MagPlaceState_Lang_12345678=<Empty>
; For alphanumeric columns in a list:
; Width of a character in "twips". The approximate column width
; is calculated by multiplying the value entered here
; by the number of characters from the column parameter setting
ColumnWidthTwipsPerAlphaCharacter=140
; For numerical columns in a list:
; Width of a character in "twips". The approximate column width is
; calculated by multiplying the value entered here by
; the number of characters from the column parameter setting
ColumnWidthTwipsPerNumericCharacter=100
; Number of data elements in the magazine list or in the
; tool list at each internal data scan.
; Range: 1 to 27, default 18.
; As of version P4.3.8.the data-scanning rate has been
; improved.
; While internal data scanning is taking place, there is no
; response to softkey actuation. This time should therefore
; not exceed 1 second.
; The value from "NumLinesPerReq" is used to scan data from a
; complete list in the background, after a list has been
; selected by pressing a softkey or after startup.
; The number of visible lines in the list is used to retrieve data
; if the data display is refreshed after changes to

Table of Contents

Other manuals for Siemens SINUMERIK

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SINUMERIK and is the answer not in the manual?

Siemens SINUMERIK Specifications

General IconGeneral
InterfaceEthernet, PROFIBUS, PROFINET, USB
Programming LanguagesDIN/ISO
DisplayTFT color display
CompatibilitySiemens drives and motors
SoftwareSINUMERIK Operate
Control Unit TypeCNC (Computer Numerical Control)
Safety FunctionsIntegrated safety functions up to SIL 3/PLe

Related product manuals