Stratasys F900 - Page 28

19
PC T12 736 / 920 12061 / 15076 8.0 T12
T12SR100
368 / 552
550 / 734
6030 / 9046
9013 / 12028
4.0
6.0
PC T16 828 / 1012 13569 / 16584 9.0 T16
T12SR100
460 / 644
644 / 828
7538 / 10553
10553 / 13569
5.0
7.0
PC T20 828 / 1012 13569 / 16584 9.0 T16
T1
2SR100
460 / 644
644 / 828
7538 / 10553
10553 / 13569
5.0
7.0
PC-ISO T12 736 / 920 12061 / 15076 8.0 T12 368 / 552 6030 / 9046 4.0
PC-ISO T16 828 / 1012 13569 / 16584 9.0 T16 460 / 644 7538 / 10553 5.0
PC-ISO T20 828 / 1012 13569 / 16584 9.0 T16 460 / 644 7538 / 10553 5.0
ST130 T20B 644 / 828 10553 / 13569 7.1 T20 828 / 1012 13569 / 16584 9.0
ULTEM 9085 T16 552 / 736 9046 / 12061 6.0 T16 460 / 644 7538 / 10553 5.0
ULTEM 9085 T20 552 / 736 9046 / 12061 6.0 T16 460 / 644 7538 / 10553 5.0
ULTEM 1010 T14 552 / 736 9046 / 12061 6.0 T16 460 / 644 7538 / 10553 5.0
ULTEM 1010 T20 552 / 736 9046 / 12061 6.0 T16 460 / 644 7538 / 10553 5.0
ULTEM 1010 T40 1500 / 1684 24581 / 27596 16.0 T20 1472 / 1656 24122 / 27137 16.0
PPSF T16 184 / 368 3015 / 6030 2.0 T16 184 / 368 3015 / 6030 2.0
ANT 800NA T20D 368 / 552 6030 / 9046 4.0 T16 460 / 644 7538 / 10553 5.0
ANT840CN03 T20D 368 / 552 6030 / 9046 4.0 T16 460 / 644 7538 / 10553 5.0
a.ABSi model material uses SR-20 support material. A T12SR20 support tip should be used (regardless of model
tip size).
ABS-M30 and ABS-M30i model material can use SR-20, SR-30, or SR-35* support material. Use the T12SR20
ti
p for SR-20 material (regardless of model tip size) and use the T12SR30 tip for SR-30 and SR-35 material
(regardless of model tip size).
ABS-ESD7 model material can use SR-30 or SR-35* support material. A T12SR30 support tip should be used
(r
egardless of model tip size).
ASA model material can use SR-30 or SR-35* support material. The T20B support tip should only be used with a
T4
0 model tip; a T12SR30 support tip should be used for all others (regardless of model tip size).
Nylon 6, Nylon 12 and Nylon 12CF model material uses SR-110 support material. A T12SR100 support tip should
be
used (regardless of model tip size). Use of Nylon 12CF requires hardened components, see head swap
procedure.
PC-ABS model material uses SR-20 support material. A T12SR20 support tip should be used (regardless of
mo
del tip size).
PC model material uses either SR-100 or PC_S support material. When using PC_S the support tip matches
mo
del tip size for T12 and T16, while T20 uses a T16 support tip. When using SR-100 use the T12SR100 support
tip (regardless of model tip size).
PC-ISO model material uses PC_S support material. Support tip size matches model tip size for T12 and T16,
wh
ile T20 uses a T16 support tip.
ST130 model material uses ST130-S support material. A T20 support tip should be used (regardless of
model tip size).
ULTEM 9085 model material uses ULT_S support material. A T16 support tip should be used (regardless of
mo
del tip size).
ULTEM 1010 model material uses U1010S1 support material. The T20 support tip should only be used with a T40
model tip; a T16 support tip should be used for all others (regardless of model tip size).
PPSF model material uses PPSF_S support material. Sup
port tip size matches model tip size.
*SR-35 requires BE V-3.20 or later.
Model
a
Material
Model
Tip
Model Tip Life
b
Support
Tip
Support Tip Life
b
Warn/Max
cu. in.
Warn/Max
cu. cm.
Warning
Canisters
Warn/Max
cu. in.
Warn/Max
cu. cm.
Warning
Canisters