Toshiba Strata CTX28 - Page 382

Telephone Button Programming
300 Series Programs
13-58 Strata CTX Programming - Part 3: Telephone Button Programming 6/04
304-19 Intercept
)% , n, +ROG
n = 1. Enable
2. Disable (default)
Enable Intercept. A call is transferred to a special destination called
intercept position when the destination of a trunk line call is not
determined with DID, DIT or DISA. Intercept is also activated when
the destination is determined, but the call cannot be terminated due to
a defect or an incorrect number. If the system has a simplified
attendant console, the attendant console is usually specified to
terminate the call. This function ensures termination of a trunk line
call.
304-20 Send Dial Tone
)% , n, +ROG
n = 1. Enable
2. Disable (default)
Enable Send Dial Tone.
304-21 TGAC Override
)% , n, +ROG
n = 1. Enable
2. Disable (default)
Enable Trunk Group Access Code (TGAC) override.
304-22 Network COS
)% , n, +ROG
n = 1~32
(default = 1)
Enter the Network COS number.
304-23 LCR Group
)% , n, +ROG
n = 1~16
(default = 1)
Enter the LCR Group number. Calls from this ILG cannot tandem if
this field is not entered.
304-24 Change COS
Override Code
)% , n, +ROG
n = 1. Enable
2. Disable (default)
Enable authority to change COS Override Code.
304-25 Register Speed Dial
Codes
)% , n, +ROG
n = 1. Enable
2. Disable (default)
Enable authority to create system speed dial codes.
304-26 Originator Invoke
OCA
)% , n, +ROG
n = 1. Enable
2. Disable (default)
Enable authority for the originator of a call to invoke OCA when
encountering a busy station.
304-27 Senderized Tone
Mode
)% , n, +ROG
n = 1. Dial Tone (default)
2. Entry Tone
3. Silence
Send DTMF tones as a complete number rather than digit-by digit.
304-28 Emergency Call
Group
)% , n, +ROG , +ROG
n = 1~8
(default = 1)
Used to enable E911 calling across a QSIG network. The QSIG ILG is
assigned to an Emergency Call Group in the same way a station is in
Program 200 FB17. Without this assignment, the call will not attempt
to complete to one of the trunks in the Emergency Group and will
result in an abandoned call. See Program 550 “Enhanced 911
Emergency Call Group” on page 13-87.
304-29 Tenant Number
)% , n, +ROG , +ROG
n = 1~8 (default = 1) Enter the Tenant number to which this DID should be assigned.
305
ILG Delete
 , +ROG
This command deletes Incoming Line Groups.
305-00 ILG Number
n,
+ROG , +ROG
n = 1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.)
Enter the ILG number to delete.
306
Outgoing Line Group
Assignment
 , +ROG
OLG is a line selection feature which enables the use of external
trunk or private line groups for outgoing service. Assign and configure
up to 128 OLGs (the same line can be placed in an OLG and an ILG).
306-00 Group Number
n,
+ROG
n = 1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.)
Enter the OLG Group number.
306-01 Group Type
)% , n, +ROG
n = 1. Analog (default)
2. ISDN
Select the OLG Type.
306-02 Trunk Type
)% , n, +ROG
n = 1. CO (default)
2. Tie
Select the Trunk Type.
Table 13-28 Programs 303~315 (continued)
Button Sequence Value(s) Summary