E.3 User Setting Table
508 YASKAWA ELECTRIC SIEP C710616 38F YASKAWA AC Drive - L1000A Technical Manual
o4-05 Capacitor Maintenance Setting
o4-07 DC Bus Pre-charge Relay Maintenance Setting
o4-09 IGBT Maintenance Setting
o4-11 U2, U3 Initialization
o4-12 kWh Monitor Initialization
o4-13 Number of Travels Counter Reset
o4-15 Maintenance Alarm Snooze Period
o4-16 Maintenance Monitoring Selection
S1-01 Zero Speed Level at Stop
S1-02 DC Injection Current at Start
S1-03 DC Injection Current at Stop
S1-04 DC Injection / Position Lock Time at Start
S1-05 DC Injection / Position Lock Time at Stop
S1-06 Brake Release Delay Time
S1-07 Brake Close Delay Time
S1-10 Run Command Delay Time
S1-11 Output Contactor Open Delay Time
S1-12 Motor Contactor Control During Auto-Tuning Selection
S1-26 Emergency Stop Start Level
S2-01 Motor Rated Speed
S2-02 Slip Compensation Gain in Motoring Mode
S2-03 Slip Compensation Gain in Regenerative Mode
S2-05 Slip Compensation Torque Detection Delay Time
S2-06 Slip Compensation Torque Detection Filter Time Constant
S3-01 Position Lock Gain at Start 1
S3-02 Position Lock Gain at Start 2 (Anti-Rollback Gain)
S3-03 Position Lock Gain at Stop
S3-04 Position Lock Bandwidth
S3-10 Starting Torque Compensation Increase Time
S3-12 Starting Torque Compensation Bias in Down Direction
S3-14 Torque Compensation Diminish Speed
S3-15 Torque Compensation Diminish Time
S3-16 Torque Limit Reduction Time
S3-20 Dwell 2 Speed Reference
S3-21 Dwell 2 End Speed
S3-25 DC Injection Gain in Regenerative Operation
S3-26 DC Injection Gain in Motoring Operation
S3-27 Torque Compensation Value with Load Condition 1
S3-28 Torque Compensation Value with Load Condition 2
S3-29 Analog Input from Load Cell with Load Condition 1
S3-30 Analog Input from Load Cell with Load Condition 2
S3-34 Anti-Rollback Torque Bias 1
S3-35 Anti-Rollback Torque Bias 2
S3-37
Position Deviation Level to Apply Anti-Rollback Torque
Bias 1
S3-38
Position Deviation Level to Apply Anti-Rollback Torque
Bias 2
S3-39 Anti-Rollback Integral Gain
S3-40 Anti-Rollback Movement Detection
S3-41 Position Lock Gain at Start Reduction
S4-01 Light Load Direction Search Selection
S4-02 Light Load Direction Search Method
S4-03 Light Load Direction Search Time
S4-04 Light Load Direction Search Speed Reference
S4-05 Rescue Operation Torque Limit
S4-06 Rescue Operation Power Supply Selection
S4-07 UPS Power
S4-08 UPS Operation Speed Limit Selection
S4-12 DC Bus Voltage during Rescue Operation
S4-13
Rescue Operation Power Supply Deterioration Detection
Level
No. Name
User
Setting
S4-15 Speed Reference Selection at Rescue Operation
S5-01 Short Floor Operation Selection
S5-02 Nominal Speed for Short Floor Calculation
S5-03 Short Floor Minimum Constant Speed Time
S5-04 Distance Calculation Acceleration Time Gain
S5-05 Distance Calculation Deceleration Time Gain
S5-10 Stopping Method Selection
S5-11 Deceleration Distance
S5-12 Stop Distance
S5-13 Direct Landing Minimum Speed Level
S6-01
Motor Contactor Response Error (SE1) Detection/Reset
Selection
S6-02 Starting Current Error (SE2) Detection Delay Time
S6-03 SE2 Detect Current Level
S6-04 Output Current Error (SE3) Detection Delay Time
S6-05 Brake Response Error (SE4) Detection Time
S6-10 Overacceleration Detection Level
S6-11 Overacceleration Detection Time
S6-12 Overacceleration Detection Selection
S6-15 Speed Reference Loss Detection
S6-16 Restart after Baseblock Selection
T1-01 Auto-Tuning Mode Selection
T1-02 Motor Rated Power
T1-03 Motor Rated Voltage
T1-04 Motor Rated Current
T1-05 Motor Base Frequency
T1-06 Number of Motor Poles
T1-07 Motor Base Speed
T1-08 Encoder Resolution (pulses per revolution)
T1-09 Motor No-Load Current (Stationary Auto-Tuning 1 and 2)
T1-10 Motor Rated Slip (Stationary Auto-Tuning 2)
T2-01 Auto-Tuning Mode Selection
T2-04 Motor Rated Power
T2-05 Motor Rated Voltage
T2-06 Motor Rated Current
T2-08 Number of Motor Poles
T2-09 Motor Base Speed
T2-10 Single Phase Stator Resistance
T2-11 Motor d-Axis Inductance
T2-12 Motor q-Axis Inductance
T2-13 Induced Voltage Constant Unit Selection
T2-14 Motor Induced Voltage Constant
T2-16 Encoder Resolution
T2-17 Encoder Offset
T2-18
Speed Reference for Auto-Tuning of PG-E3 Encoder
Characteristics
T2-19
Rotation Direction for Auto-Tuning of PG-E3 Encoder
Characteristics
No. Name
User
Setting
SIEP_C710616_38F_5_0.book 508 ページ ２０１５年１１月９日 月曜日 午後３時３６分
To Next Page
Loading...
