Barco SIM 7Q HB

To Next Page
To Previous Page
Table of contents
4.4 Save as (create a custom ﬁle)................................................................................................95
4.5 Rename ﬁle ................................................................................................................... 96
4.6 Copy...........................................................................................................................97
4.7 Delete .........................................................................................................................98
4.8 Forced ﬁle load................................................................................................................99
5 Geometry ...........................................................................................................................100
5.1 Introduction. . . ................................................................................................................101
5.2 Geometry ﬁles................................................................................................................102
5.3 Accessing the Geometry menu .............................................................................................103
5.4 Geometry distortions.........................................................................................................104
5.5 Load . . ........................................................................................................................107
5.6 Edit ...........................................................................................................................108
5.6.1 Accessing the Geometry Edit menu .................................................................................109
5.6.2 Geometry Edit wizard .................................................................................................110
5.6.3 Geometry Edit Modes .................................................................................................112
5.6.4 Editing a geometry ﬁle ................................................................................................114
5.6.5 Axis link................................................................................................................123
5.6.6 Shift Adjustment.......................................................................................................126
5.6.7 Transport Delay .......................................................................................................128
5.6.8 Sharpness.............................................................................................................130
5.6.9 Geometry Reset .......................................................................................................131
5.6.9.1 Reset all levels ..................................................................................................132
5.6.9.2 Restore to a level ...............................................................................................133
5.7 Rename a Geometry File . . ..................................................................................................135
5.8 Copy a Geometry File .......................................................................................................136
5.9 Delete a Geometry File ......................................................................................................137
6 Lamp................................................................................................................................138
6.1 Runtimes ....................................................................................................................139
6.2 Lamp runtime warning.......................................................................................................140
6.3 History........................................................................................................................141
6.4 Reset lamp Runtime .........................................................................................................142
6.5 Lamp power mode (only for SIM 7Q & SIM 7Q HC)........................................................................143
6.6 CLO Mode....................................................................................................................144
6.6.1 Constant Light Output (CLO) .........................................................................................145
6.6.2 CLO Target ............................................................................................................146
7 General .............................................................................................................................147
7.1 Pause.........................................................................................................................148
7.2 Freeze........................................................................................................................149
7.3 Identiﬁcation..................................................................................................................150
8 Display setup .......................................................................................................................151
8.1 Textbox .......................................................................................................................152
8.2 Menu bar position............................................................................................................153
8.3 Slider box position .......................................................................................................... .154
8.4 Sync variance limit...........................................................................................................155
8.5 Soft edge .....................................................................................................................157
8.5.1 Introduction ............................................................................................................158
8.5.2 Accessing the Soft edge menu .......................................................................................160
8.5.3 Soft edge edit. .........................................................................................................161
8.5.3.1 The soft edge edit wizard ......................................................................................162
8.5.3.2 The soft edge edit modes.......................................................................................163
8.5.3.3 Creating/editing a soft edge . . ..................................................................................165
8.5.3.4 Alpha planes . . ..................................................................................................171
8.5.4 Black level .............................................................................................................173
8.5.4.1 Introduction ......................................................................................................174
8.5.4.2 Internal black level ..............................................................................................175
8.5.4.3 Beta planes......................................................................................................176
8.5.5 Blanking ...............................................................................................................177
8.6 Auto Image Setup............................................................................................................178
8.7 Smearing reduction (Optional)...............................................................................................179
8.7.1 Introduction ............................................................................................................180
8.7.2 Enabling Smearing reduction . . .......................................................................................181
8.7.3 Adjusting the phase .. .................................................................................................182
8.8 True motion reproduction . . ..................................................................................................183
8.9 Color temperature........................................................................................................... .184
8.10 Dynacolor ....................................................................................................................185
8.10.1 Introduction ............................................................................................................186
8.10.2 Enabling DynaColor...................................................................................................192
8.10.3 Dynacolor adjustment.................................................................................................193
8.10.3.1 Introduction ......................................................................................................194
8.10.3.2 Calibration (for multiple projectors).............................................................................196
8.10.3.3 Common color values...........................................................................................199
8.10.3.4 Factory preset...................................................................................................200
8.10.4 Black color matching..................................................................................................201
8.10.4.1 Introduction ......................................................................................................202
8.10.4.2 Black Color adjustment .........................................................................................203
8.10.5 CLO-TOD color tracking ..............................................................................................204
2
R59770066 SIM 7Q SERIES 07/10/2013
Main Page
Barco SIM 7Q HB - Page 6

Table of Contents

Related product manuals
