DURKOPP ADLER 867 - Page 130

DURKOPP ADLER 867

164 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Disposal

128 Service Instructions 867 - 04.0 - 10/2019

Table of Contents

Default Chapter3
- Table of Contents3
1 About These Instructions7
- For Whom Are These Instructions Intended7
- Representation Conventions - Symbols and Characters7
- Other Documents8
- Liability9
2 Safety11
- Basic Safety Instructions11
- Signal Words and Symbols Used in Warnings12
3 Working Basis15
- Order of the Adjustments15
- Laying the Cables15
- Removing the Covers16
- Tilting the Machine Head16
- Assembling and Disassembling the Arm Cover17
- Assembling and Disassembling the Head Cover18
- Assembling and Disassembling the Valve Cover19
- Opening and Closing the Throat Plate Slides20
- Assembling and Disassembling the Throat Plate21
- Assembling and Disassembling the Feed Dog22
- Flats on Shafts23
- Locking the Machine in Place24
- Adjusting the Handwheel into Position26
4 Adjusting the Handwheel Scale27
5 Positioning the Arm Shaft28
6 Toothed Belt Wheels29
- Positioning the Upper Toothed Belt Wheel29
- Positioning the Lower Toothed Belt Wheel31
7 Adjusting the Stitch Length Adjusting Wheels32
- Adjusting the Upper Stitch Length Adjusting Wheel33
- Adjusting the Lower Stitch Length Adjusting Wheel34
- Adjusting the Stitch Length Limit35
- Adjusting the Eccentric for the Forward and Backward Stitches36
8 Feed Dog37
- Adjusting the Feed Dog Position37
- Moving the Feed Dog38
- Moving the Feed Dog Carrier39
- Adjusting the Feed Dog Movement40
- Adjusting the Feed Movement40
- Adjusting the Feed Dog Height at Top Dead Center41
- Feed Dog Lift (Default)42
- Adjusting the Stroke Movement42
- Adjusting the Compensating Weight43
- Feed Dog Lift (Adjustable Stroke Eccentric)44
- Adjusting the Stroke Movement44
- Adjusting the Stroke Eccentric45
9 Aligning the Needle Bar Linkage47
- Aligning the Needle Bar Linkage Sideways47
- Aligning the Needle Bar Linkage in the Sewing Direction49
10 Position of the Hook and Needle51
- Adjusting the Hook Side Clearance51
- Adjusting the Looping Stroke Position52
- Adjusting the Needle Guard54
- Adjusting the Needle Bar Height55
11 Adjusting the Bobbin Case Lifter56
- Adjusting the Lifting Gap57
- Adjusting the Timing for Lifting58
12 Sewing Feet59
- Adjusting an Even Sewing Foot Stroke60
- Adjusting the Stroke Movement for the Walking Foot61
- Adjusting the Sewing Foot Pressure62
- Adjusting the Sewing Foot Lifting Height63
13 Adjusting the Needle Thread Tension64
- Adjusting the Needle Thread Regulator64
- Adjusting the Thread Tensioning Spring65
14 Winder66
- Adjusting the Winder Wheel and the Driver Wheel (Long Arm Machines)66
- Adjusting the Winder67
- Adjusting the Hook Thread Guide70
15 Thread Trimmer71
- Adjusting the Height of the Thread-Pulling Knife71
- Adjusting the Cutoff Curve72
- Adjusting the Cutting Pressure74
- Adjusting Point in Time for Cutting75
16 Short Thread Cutter (KFA)76
- General Information77
- Adjusting the Locking Latch79
- Adjusting the Thread-Pulling Knife80
- Adjusting the Counter Blade81
- Adjusting Point in Time for Cutting83
17 Adjusting the Potentiometer85
18 Adjusting the Safety Snap-On Coupling87
- Attaching the Safety Release Clutch87
- Adjusting the Torque88
19 Machines with Integrated Motor89
- Overview of the Components89
- Disassembling the Drive90
- Disassembling the Handwheel and Handwheel Flange90
- Disassembling the Cover91
- Disassembling the Encoder92
- Disassembling the Stator93
- Disassembling the Rotor94
- Assembling the Drive95
- Assembling the Rotor95
- Assembling the Stator96
- Assembling the Encoder97
- Assembling the Cover98
- Locking the Machine in Place99
- Assembling the Handwheel Flange99
- Assembling the Handwheel100
- Replacing the Fuse of the Sewing Light Transformer101
- Replacing the PCB101
20 Special Machines102
- Machines with Switchable Needle Bars102
- Adjusting the Needle Bar Height102
- Adjusting the Slide104
- Machines with Moving Binder105
- Machines with Edge Trimmer106
- Adjusting the Time for Knife Movement106
- Adjusting the Knife Stroke107
- Adjusting the Blade Overlap108
- Adjusting the Position and Pressure of the Cutting Edges108
21 Programming109
- Activating the Tensioner Lift113
- Activating the NSB114
22 Maintenance115
- Cleaning116
- Lubricating118
- Lubricating the Machine Head119
- Adjusting the Hook Lubrication120
- Servicing the Pneumatic System121
- Adjusting the Operating Pressure121
- Draining the Water-Oil Mixture122
- Cleaning the Filter Element123
- Servicing Specific Components124
- Cleaning the Motor Fan Mesh124
- Checking the Toothed Belt125
- Parts List125
23 Decommissioning127
24 Disposal129
25 Troubleshooting131
- Customer Service131
- Messages of the Software131
- Information Messages131
- Error Messages134
- Errors in Sewing Process137
26 Technical Data139
- Noise Emission139
- Data Overview by Subclasses140
- Permissible Maximum Speeds149
- Requirements for Fault-Free Operation154
27 Appendix155

Other manuals for DURKOPP ADLER 867

Parts List153 pages

Durkopp Adler192 pages

Operating Manual120 pages

Instruction Manual70 pages

Additional Instructions20 pages

Instructions16 pages

Related product manuals

Preview: DURKOPP ADLER M-TYPE 867

DURKOPP ADLER M-TYPE 867

Preview: DURKOPP ADLER 867-M Premium

DURKOPP ADLER 867-M Premium

DURKOPP ADLER 869-M Premium

Preview: DAC BASIC - CLASS 867 MANUAL PART II V 12-2010

DAC BASIC - CLASS 867 MANUAL PART II V 12-2010

DURKOPP ADLER 806

Preview: DURKOPP ADLER 888

DURKOPP ADLER 888

DURKOPP ADLER 887

Preview: DURKOPP ADLER 827

DURKOPP ADLER 827

DURKOPP ADLER 8967

DURKOPP ADLER 8700

Preview: DURKOPP ADLER 887 Series

DURKOPP ADLER 887 Series

Preview: DURKOPP ADLER 878-M PREMIUM

DURKOPP ADLER 878-M PREMIUM