Endress+Hauser Proline Promass E 500 - Table of Contents

Proline Promass E 500 PROFIBUS PA Table of contents
Endress+Hauser 3
Table of contents
1 About this document ................ 6
1.1 Document function ..................... 6
1.2 Symbols .............................. 6
1.2.1 Safety symbols .................. 6
1.2.2 Electrical symbols ................ 6
1.2.3 Communication-specific symbols ..... 6
1.2.4 Tool symbols .................... 7
1.2.5 Symbols for
certain types of information ......... 7
1.2.6 Symbols in graphics ............... 7
1.3 Documentation ........................ 8
1.4 Registered trademarks ................... 8
2 Safety instructions .................. 9
2.1 Requirements for the personnel ............ 9
2.2 Intended use .......................... 9
2.3 Workplace safety ...................... 10
2.4 Operational safety ..................... 10
2.5 Product safety ........................ 10
2.6 IT security ........................... 11
2.7 Device-specific IT security ................ 11
2.7.1 Protecting access via hardware write
protection ..................... 11
2.7.2 Protecting access via a password .... 11
2.7.3 Access via web server ............ 12
2.7.4 Access via service interface (CDI-
RJ45) ........................ 12
3 Product description ................ 14
3.1 Product design ........................ 14
3.1.1 Proline 500 – digital ............. 14
3.1.2 Proline 500 .................... 15
4 Incoming acceptance and product
identification ..................... 16
4.1 Incoming acceptance ................... 16
4.2 Product identification ................... 16
4.2.1 Transmitter nameplate ........... 17
4.2.2 Sensor nameplate ............... 19
4.2.3 Symbols on the device ............ 20
5 Storage and transport ............. 21
5.1 Storage conditions ..................... 21
5.2 Transporting the product ................ 21
5.2.1 Measuring devices without lifting
lugs ......................... 21
5.2.2 Measuring devices with lifting lugs .. 22
5.2.3 Transporting with a fork lift ........ 22
5.3 Packaging disposal ..................... 22
6 Installation ....................... 22
6.1 Mounting requirements ................. 22
6.1.1 Installation position ............. 22
6.1.2 Environmental and process
requirements .................. 25
6.1.3 Special installation instructions ..... 26
6.2 Installing the measuring instrument ........ 29
6.2.1 Required tools .................. 29
6.2.2 Preparing the measuring instrument . 29
6.2.3 Mounting the measuring device ..... 29
6.2.4 Mounting the transmitter housing:
Proline 500 – digital ............. 30
6.2.5 Mounting the transmitter housing:
Proline 500 .................... 32
6.2.6 Turning the transmitter housing:
Proline 500 .................... 33
6.2.7 Turning the display module: Proline
500 ......................... 33
6.3 Post-installation check .................. 34
7 Electrical connection .............. 35
7.1 Electrical safety ....................... 35
7.2 Connecting requirements ................ 35
7.2.1 Required tools .................. 35
7.2.2 Requirements for connection cable ... 35
7.2.3 Terminal assignment ............. 40
7.2.4 Available device plugs ............ 40
7.2.5 device plug pin assignment ........ 41
7.2.6 Shielding and grounding .......... 41
7.2.7 Preparing the measuring device ..... 42
7.3 Connecting the measuring instrument:
Proline 500 - digital .................... 43
7.3.1 Connecting the connecting cable .... 43
7.3.2 Connecting the signal cable and the
supply voltage cable ............. 48
7.4 Connecting the measuring instrument:
Proline 500 .......................... 50
7.4.1 Fitting the connecting cable ........ 50
7.4.2 Connecting the signal cable and the
supply voltage cable ............. 54
7.5 Potential equalization .................. 56
7.5.1 Requirements .................. 56
7.6 Special connection instructions ............ 57
7.6.1 Connection examples ............. 57
7.7 Hardware settings ..................... 60
7.7.1 Setting the device address ......... 60
7.7.2 Activating the default IP address .... 61
7.8 Ensuring the degree of protection .......... 63
7.9 Post-connection check .................. 63
8 Operation options ................. 64
8.1 Overview of operation options ............ 64