Flintec FT-111 - Sealing of Approved Scale; Sealing With Sticker

137 pages

Save Page as PDF

To Next Page

To Previous Page

FT-111, User Manual Rev. 2.0.0, June 2022 Page 75 of 137

10 SEALING OF APPROVED SCALE

Sealing

With sticker

Main Page

Table of Contents2
Safety Instructions5
Introduction6
Overview6
Specifications6
Housing10
Mounting Kits10
The Front View and Key Functions12
Display12
Keypad14
Installation15
Recommendations15
Environment15
Mechanical Installation Recommendations15
Cabling Recommendations15
Electrical Connection Recommendations16
Installation Steps17
Step 1: Preliminary Preparations17
Step 2: Mechanical Installation17
Step 3: Open the Housing / Close the Housing19
Step 4A: Analogue Load Cell Connection19
Step 4B: Digital Load Cell Connection (Only FT-111 D)20
Step 5: RS 232C Serial Ports21
Step 6: RS 485 Serial Port22
Step 7: Ethernet TCP/IP22
Step 8: USB Port23
Step 9: Alibi Memory24
Step 10: Optional Board Installation24
Step 11: Power Source Connection and Grounding24
Step 12: Scale Setup and Calibration25
Step 13: Use25
Installation of Optional Boards26
Cleaning27
Disposal27
Functions28
Basic Functions28
Advanced Functions29
Backup and Restore (with SD Card)31
Setup, Backup and Restore Via Indface2X Software32
Firmware Upgrade32
Copying the Weighing-Related Data from SD Card to a PC32
Digital Inputs and Outputs33
Digital Inputs34
Digital Outputs34
RS232 and RS485 Data Outputs39
Continuous Data Output39
Fast Continuous Data Output40
Print Mode40
EPL Format42
BSI Data Structure for Dialog with PC42
Fieldbus Interface42
Programming and Calibration43
Alphanumeric Entry for Headers and Footers43
Entering to the Programming and Calibration44
Quick Access Parameter Blocks Used Frequently44
Exit from Programming44
Programming and Parameters45
[1-- INTERFACE] Interface Block46
[2-- CONFIGURATIO] Configuration Block56
[3-- APPLICATION] Application Block58
[5-- SCALE] Scale Block61
[6-- CALB / ADJUST] Calibration and Adjustment Block64
[8-- METROLOGY] Metrology Block65
[9-- DIAGNOSTIC] Diagnostic Block66
Calibration68
Linearity Correction68
Zero and Span Adjustments69
Ecal Electronic Calibration70
Gravity Adjustment71
Calibration Coefficients71
Digital Load Cells (DLC)72
Addressing of Digital Load Cells72
Sealing of Approved Scale75
Optional Boards76
Digital Inputs and Outputs76
Alibi Memory77
Installation of Alibi SD Card77
Activating Alibi Memory78
How Is the Data Recorded into the Alibi Memory78
Recall Data from Alibi Memory78
Installation of SD Card80
BSI Protocol to Interface with PC and PLC81
BSI-Base Commands82
Continuous Data Formats88
Analogue Output91
Analogue Output Connection91
Modbus RTU93
Modbus RTU Data Structure93
Ethernet TCP/IP99
Ethernet Parameters99
Modbus TCP Data Structure100
Profibus DP101
Electrical Connection101
Data Format102
GSD Configuration102
Profibus DP Data Structure102
Profinet103
Electrical Connection104
Data Format104
Profinet Parameters105
GSDML Configuration105
Profinet Data Structure106
Ethernet/Ip107
Electrical Connection108
Data Format109
Ethernet/Ip Parameters109
EDS Configuration109
Ethernet/Ip Data Structure110
Ethercat111
Electrical Connection112
Data Format112
ESI Configuration113
Ethercat Data Structure113
CC-Link114
Electrical Connection114
Data Format115
CC-Link Configuration115
4CC-Link Data Structure115
Powerlink116
Electrical Connection117
Data Format117
3XDD Configuration118
Powerlink Data Structure118
Appendix 1 Data Structure Profibus, Profinet, Ethernet/Ip, Ethercat, CC-Link, Powerlink119
Appendix 2: Data Structure Canopen126
Error Codes135

Flintec FT-111 - Sealing of Approved Scale; Sealing With Sticker

Table of Contents

Related product manuals