What to do if my GE Analytical Instruments displays a Fluid Leak in Optional C1D2 or ATEX Enclosure Error?
This error indicates that a large leak has been detected inside the optional outer enclosure. You should resolve the source of the leak and then clean and dry the sensor.
How to troubleshoot Carrier Bypass Gas Flow Error on GE Measuring Instruments?
To address a Carrier Bypass Gas Flow Error on your GE Measuring Instruments, go to the Diagnostics screen and run the Gas Valves test (V1-R). If the gas flow rate fails to maintain 165 cc/min, there may be an issue.
What does it mean when my GE Analytical Instruments displays an Oxidizer Error?
This error indicates that the level sensor in the oxidizer container is indicating that the container should be refilled. Refill the oxidizer container.
What does it mean when my GE Analytical Instruments displays a Dilution Water Error?
This error indicates that the level sensor in the dilution water container is indicating that the container should be refilled. Refill the dilution water container.
What does it mean when my GE Analytical Instruments displays a Check Standard Error?
This error indicates that the level sensor in the check standard container is indicating that the container should be refilled. Refill the check standard container.
What to do if iButton Read Error appears on GE Sievers Innovox?
Please power cycle the Analyzer if your GE Measuring Instruments displays an iButton Read Error.
What should I do if the Tubing Life Error appears on my GE Sievers Innovox Measuring Instruments?
If your GE Measuring Instruments displays a Tubing Life Error, replace the tubing in all pinch valves.
How to fix Gas Inlet Pressure Error in GE Measuring Instruments?
To resolve a Gas Inlet Pressure Error on your GE Measuring Instruments, check the source gas. Ensure that your lines are connected and that there is sufficient pressure.
Why does my GE Analytical Instruments display a Reactor Cooling Error?
This error indicates that the reactor did not cool down within the allotted time. If the IP56 option is installed, wash the air filter if it is dirty. Otherwise, check for obstructions at the reactor cooling air inlet and outlet (bottom and right side of case). Run the Heater test from the Diagnostics screen, and check for air flow out of the reactor cooling air outlet after 190 seconds. Export the errors and contact GE Analytical Instruments for further instructions.
What does it mean when my GE Analytical Instruments displays a Check Standard Warning?
This warning indicates that the Check Standard solution may have changed concentration, the tolerance limits may need adjustment, or the Analyzer may require calibration. Replace the check standard and repeat the measurement. If the warning persists, the Analyzer may need calibration.
General| Category | Measuring Instruments |
|---|---|
| Brand | GE |
| Model | Sievers Innovox |
| Response Time | Typically 2 minutes |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Communication Interfaces | USB, Ethernet |
| Certifications | CE |
| Humidity Range | 10% to 90% non-condensing |
Provides detailed technical specifications for the InnovOx TOC Analyzer.
Discusses sample species that can form toxic products or react violently.
Details interferences that can affect component longevity and performance.
Explains how inorganic compounds can affect measurement accuracy.
Procedure for connecting the waste tube to a drain.
Details on connecting various cables and I/O interfaces.
Instructions for safely connecting the analyzer to AC power.
Guidance on connecting sample streams to the analyzer.
Procedures for installing the wastewater sampler.
Guides initial power-up and basic analyzer configuration.
Procedure to confirm the analyzer is operating correctly.
Step-by-step guide to performing the calibration process.
Instructions for reviewing and modifying calibration measurements.
Defines measurement settings for Online, Check Standard, Grab, and Rinse modes.
Guides on setting up online measurements for various features.
Details parameters for NPOC, TOC, TC, and IC measurements.
Procedure for measuring carbon concentrations in reagents for blank correction.
Guides on configuring analyzer interfaces and connections.
Steps to manually configure IP settings for network connection.
Safe procedures for powering down the analyzer.
Procedure for lubricating the analyzer's syringes every three months.
Six tests to locate leaks in the gas delivery system.
Correction for carbon contribution from reagents.
To Next Page
