GE Sievers Innovox - User Manual

Questions and Answers:

K
Kimberly GarciaAug 29, 2025
What does it mean when my GE Analytical Instruments displays a Gas Flow Regulation Error?
- M
  michelle29Aug 29, 2025
  This error means that the PID Test has either failed to stabilize in the allotted time or is outside the acceptable range. To resolve this: 1. Determine which Gas Valve PID settings should be selected by identifying which Gas Manifold is installed in your instrument. 2. Verify the appropriate PID option is activated in the Analyzer (Maintenance > Advanced). 3. Perform the Gas Leak Check diagnostics to identify any other possible problems. If the error continues, contact GEAI Technical Support for guidance.
F
fthomasSep 22, 2025
What to do if iButton Read Error appears on GE Sievers Innovox?
- R
  Rebecca OwenSep 22, 2025
  Please power cycle the Analyzer if your GE Measuring Instruments displays an iButton Read Error.
R
Rebecca HayesSep 16, 2025
What are the steps to fix Reactor Leak Error on GE Sievers Innovox?
- J
  Jonathan BennettSep 17, 2025
  To resolve a Reactor Leak Error on your GE Measuring Instruments, go to the Diagnostics screen and run the Gas Leak tests.
P
Patrick RichardsonAug 31, 2025
Why does my GE Analytical Instruments display a Reactor Cooling Error?
- R
  Randy NealAug 31, 2025
  This error indicates that the reactor did not cool down within the allotted time. If the IP56 option is installed, wash the air filter if it is dirty. Otherwise, check for obstructions at the reactor cooling air inlet and outlet (bottom and right side of case). Run the Heater test from the Diagnostics screen, and check for air flow out of the reactor cooling air outlet after 190 seconds. Export the errors and contact GE Analytical Instruments for further instructions.
M
Michael EdwardsAug 31, 2025
What does it mean when my GE Analytical Instruments displays a Check Standard Warning?
- C
  Christopher WillisAug 31, 2025
  This warning indicates that the Check Standard solution may have changed concentration, the tolerance limits may need adjustment, or the Analyzer may require calibration. Replace the check standard and repeat the measurement. If the warning persists, the Analyzer may need calibration.
L
Lisa HartAug 31, 2025
What does it mean when my GE Analytical Instruments displays a Gas Inlet Pressure Error?
- C
  Christina TylerSep 1, 2025
  This error indicates an issue with the gas supply. Check the source gas to ensure lines are connected and there's sufficient pressure. If using an air purifier, verify it is powered and functioning. If the problem continues, export the errors and contact GE Analytical Instruments for further assistance.
G
gregory92Sep 1, 2025
What does it mean when my GE Analytical Instruments displays a Sparger Gas Flow Error?
- V
  Veronica StantonSep 1, 2025
  This error indicates that the gas flow rate through the sparger is too low. To resolve this, go to the Diagnostics screen and run the Gas Valves test (V7-SH). If the gas flow rate fails to maintain 200 cc/min, export the errors and contact GE Analytical Instruments for further assistance.
B
Benjamin LewisSep 1, 2025
What does it mean when my GE Analytical Instruments displays a Carrier Bypass Gas Flow Error?
- K
  krista76Sep 1, 2025
  This error indicates that the flow rate of carrier gas through valve V1-R is too low. Go to the Diagnostics screen and run the Gas Valves test (V1-R). If the gas flow rate fails to maintain 165 cc/min, export the errors and contact GE Analytical Instruments for further assistance.
G
Gary GordonSep 2, 2025
What does it mean when my GE Analytical Instruments displays a Reactor Gas Flow Error?
- M
  michaelwalkerSep 2, 2025
  This error indicates that the flow rate of carrier gas through valve V2-R is too low. Go to the Diagnostics screen and run the Gas Valves test (V2-R). If the gas flow rate fails to maintain 165 cc/min, export the errors and contact GE Analytical Instruments for further assistance.
K
Kayla MaloneSep 22, 2025
What should I do if the Datastore Error appears on my GE Sievers Innovox Measuring Instruments?
- H
  hugheskimberlySep 22, 2025
  If your GE Measuring Instruments displays a Datastore Error, please shut down the Analyzer and power cycle it.

GE Sievers Innovox Specifications

General

Category	Measuring Instruments
Brand	GE
Model	Sievers Innovox
Response Time	Typically 2 minutes
Power Supply	100-240 VAC, 50/60 Hz
Communication Interfaces	USB, Ethernet
Certifications	CE
Humidity Range	10% to 90% non-condensing