What does it mean when my GE Analytical Instruments shows a Tubing Life Warning?
Based on the history of usage, the Analyzer estimates that only two weeks of pinch valve tubing remains. Order tubing from GE now to avoid down time and more costly failures of pinch valves.
What does it mean when my GE Analytical Instruments shows a Peristaltic Pump Life Warning?
Based on the history of usage, the Analyzer estimates that only two weeks of peristaltic pump life remains. Order two new peristaltic pumps from GE now to avoid down time when the pumps expire.
What does a CO2 Gas Leak Detected Warning mean on my GE Analytical Instruments, and what should I do?
This warning indicates that CO2 was detected by the NDIR when it should not have been present. To address this: - Perform a Reactor Liquid Flow test and a Bypass Liquid Flow test. - Perform the gas leak tests in diagnostics to ensure the system isn't leaking. - Continue running the sample. If the warning continues, consider replacing the reactor seals, pinch tubing, and water in GLS.
What to do if my GE Analytical Instruments displays a Tubing Life Error?
The Analyzer estimates that the pinch valve tubing life has expired, based on its usage history. Order tubing from GE to prevent downtime and more costly pinch valve failures.
Why does my GE Analytical Instruments show a Peristaltic Pump Life Error?
This error appears because, based on its usage history, the analyzer estimates that the peristaltic pump in the Sample Handling and Reactor modules has reached the end of its life. To resolve this, order two new peristaltic pumps from GE.
What to do if my GE Analytical Instruments displays a Touchscreen Error?
Please shut down the Analyzer and power cycle. If the problem persists, shut down the Analyzer and power down. Then, check the cable connections. You may be able to regain control of the unit by plugging a mouse into any of the USB port. If the problem persists please export the errors and contact GE Analytical Instruments for further instructions.
How to resolve Software Invalid State Error on GE Analytical Instruments?
Please power cycle the Analyzer. If the problem persists, export errors and contact GE Analytical Instruments for further instructions and analysis.
What should I do if my GE Analytical Instruments displays Stream 4 Flow Warning?
Check that water is flowing in the sample cup and the inlet valve (if installed) is properly adjusted. If the problem persists, please export the warnings and contact GE Analytical Instruments for further instructions.
What to do if my GE Analytical Instruments displays a PDF Document Error?
Shutdown the Analyzer and then power cycle the Analyzer. If the problem persists, please export the errors and contact GE Analytical Instruments for further instructions.
What to do if my GE Analytical Instruments displays an Internal Communications Error?
This indicates that a module in the Analyzer is not communicating over the bus. Please power cycle the Analyzer. If the problem persists, consult the Operation and Maintenance Manual for further instructions.
General| Category | Measuring Instruments |
|---|---|
| Brand | GE |
| Model | Sievers Innovox |
| Response Time | Typically 2 minutes |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Communication Interfaces | USB, Ethernet |
| Certifications | CE |
| Humidity Range | 10% to 90% non-condensing |
Provides detailed technical specifications for the InnovOx TOC Analyzer.
Discusses sample species that can form toxic products or react violently.
Details interferences that can affect component longevity and performance.
Explains how inorganic compounds can affect measurement accuracy.
Procedure for connecting the waste tube to a drain.
Details on connecting various cables and I/O interfaces.
Instructions for safely connecting the analyzer to AC power.
Guidance on connecting sample streams to the analyzer.
Procedures for installing the wastewater sampler.
Guides initial power-up and basic analyzer configuration.
Procedure to confirm the analyzer is operating correctly.
Step-by-step guide to performing the calibration process.
Instructions for reviewing and modifying calibration measurements.
Defines measurement settings for Online, Check Standard, Grab, and Rinse modes.
Guides on setting up online measurements for various features.
Details parameters for NPOC, TOC, TC, and IC measurements.
Procedure for measuring carbon concentrations in reagents for blank correction.
Guides on configuring analyzer interfaces and connections.
Steps to manually configure IP settings for network connection.
Safe procedures for powering down the analyzer.
Procedure for lubricating the analyzer's syringes every three months.
Six tests to locate leaks in the gas delivery system.
Correction for carbon contribution from reagents.
To Next Page
