GRAUPNER mz-24 PRO - Page 155

Basic Operating Steps
• ST OFF or ST ON Button
Touch this button to turn on or off the graphic and
numeric display of the control stick position.
When ST ON on is selected and the control ele-
ments (throttle/pitch control stick) is moved, a ver-
tical green line moves synchronously in the graph
between the two endpoints L and H. The control
stick position is also displayed numerically in the
IN line (-100 % to +100 %). The intersection of this
line with the curve is identified as OUT and can be
varied at the support points between -125% and
+125%. Control signals changed in this way affect
all of the subsequent mixing and coupling func-
tions.
In the example below, the control stick is exact-
ly halfway between the middle and end of its path,
at +50% of the control path, and generates an out-
put signal that is also +50% due to the linear char-
acteristic:
PHASE 1
SERVO
PITCHK
BACK
IN
OUT
POINT
OFF
INC
ENT
DEC
Y-axis
TRIM
X-axis
ST ON
Curve
+050%
+050%
000%
?
Pitch min.
FORWARD
Between the two endpoints L and H, up to 5 ad-
ditional support points can be set, though the dis-
tance between support points may not be less
than 25%.
• ENT Button
Move the control stick. Support points can be set
by touching the ENT button whenever a question
mark ? shows in the POINT line. A green point ap-
pears at the intersection of the yellow and green
lines:
PHASE 1
SERVO
PIT>>TAIL
BACK
IN
OFF
POINT
OFF
INC
ENT
DEC
Y-axis
TRIM
X-axis
ST ON
Curve
+050%
+050%
000%
?
Pitch min.
FORWARD
Press
When the control stick is moved and the green line
moves off the green point, the point will turn red,
the ? is replaced with a number, and the point val-
ue appears in the value field to the right of the sup-
port point number:
PHASE 1
SERVO
PIT.CRV
BACK
ON
OFF
POINT
OFF
INC
ENT
DEC
Y-axis
TRIM
X-axis
ST ON
Curve
+050%
+050%
+050%
1
Pitch min.
FORWARD
The 5 support points between the L and H end-
points can be created in any order; support points
are automatically renumbered sequentially from
left to right after points are set or deleted. In the
example below, the red point at left near the L end-
point is now considered Point 1:
PHASE 1
SERVO
PIT.CRV
BACK
IN
OUT
POINT
OFF
INC
ENT
DEC
Y-axis
TRIM
X-axis
ST ON
Curve
–050%
–050%
–050%
1
Pitch min
FORWARD
Deleting a Support Point
To remove a set support point, move the control
stick until the vertical green line aligns with the
point to be deleted. The support point will turn red
and its number and associated value will appear in
the POINT line. Press the ENT button to remove
the point:
PHASE 1
SERVO
PIT.CRV
BACK
IN
OUT
POINT
OFF
INC
ENT
DEC
Y-axis
TRIM
X-axis
ST ON
KURVE
000%
000%
000%
2
Pitch min
FORWARD
Press
The red point disappears:
PHASE 1
SERVO
PIT.CRV
BACK
IN
OUT
POINT
OFF
INC
ENT
DEC
Y-axis
TRIM
X-axis
ST ON
CURVE
000%
000%
000%
?
Pitch min
FORWARD
Changing the Support Point Value
• X-axis Button (X-axis)
Activate this function, press to highlight the button
at the bottom edge of the display.
Move the active (red) point to the right by pressing
the INC button or to the left with the DEC but-
ton, as shown below:
PHASE 1
SERVO
PIT.CRV
BACK
IN
OUT
POINT
OFF
INC
ENT
DEC
Y-axis
TRIM
X-axis
ST ON
CURVE
–036%
000%
000%
2
Pitch min
FORWARD
Press the X-axis button again to deactivate the
function.
155
Function menu | Helicopter model - Pitch curve