GRAUPNER mz-24 PRO - Page 70

after about 3 seconds, the red LED goes dark for
about 3 seconds. Release the SET button on the
receiver. As long as the LED is dark, the receiver is
in binding mode.
As described in the above GR-16 and GR-24 bind
procedure, within the 3 second window, start bind-
ing the receiver to the current model memory by
touching one of the two buttons in the BIND ON/
OFF line.
Binding has been successful if the receiver LED
remains dark and the receiver display switches
to 6CH .
If the red receiver LED shines red again, the bind-
ing process was unsuccessful. The CHK button
in the BIND ON/OFF Line will automatically turn
to OFF. Change the antenna position and try the
entire procedure again.
TX OUT SET (Receiver Output)
The mz-24 Pro HoTT transmitter allows users to dis-
tribute the transmitter control channels within a re-
ceiver as desired. In addition, users can distribute
the 12 receiver control channels to the two receivers
as preferred. This distribution process is called "map-
ping" or "channel mapping".
Press the applicable receiver to be mapped in the TX
OUT SET line, in the example below RX1 is chosen:
BACK
TX OUT SET
RF ON/OFF
RANGE TEST
BIND ON/OFF
SET
OFF
ON
12CH
RX1
RX2
DSC OUTPUT
SET
OFF
PPM10
NORMAL
RF TYPE
99sec
OFF
AUTOLOG
TX ctl
Press
• If there is no reaction other than a "beep", the RF
module is switched off. Switch the RF module on
and repeat the process.
• If an active warning window appears, the RF mod-
ule of the transmitter is switched off but there is no
connection with the receiver:
OK
Can not receive data
Warning
Press OK. Turn the receiver system on and/or bind
the receiver and repeat the process.
Channel Assignment Within a Receiver
Users can distribute transmitter control channels (re-
ceiver inputs) to the outputs (servo connections), of
the selected receiver. Select the desired output to
map by pressing on the related channel button:
BACK
PHASE 1
TX
TX
TX
TX
1
TX
TX
2
3
4
5
6
CH >> OUT1
CH >> OUT2
CH >> OUT3
CH >> OUT4
CH >> OUT5
CH >> OUT6
TX
TX
TX
TX
7
TX
TX
8
9
10
11
12
CH >> OUT7
CH >> OUT8
CH >> OUT9
CH >> OUT10
CH >> OUT11
CH >> OUT12
DEC
RES
INC
SERVO
Out.Swap
Press
The field highlights blue:
BACK
PHASE 1
TX
TX
TX
TX
1
TX
TX
2
3
4
5
6
CH >> OUT1
CH >> OUT2
CH >> OUT3
CH >> OUT4
CH >> OUT5
CH >> OUT6
TX
TX
TX
TX
7
TX
TX
8
9
10
11
12
CH >> OUT7
CH >> OUT8
CH >> OUT9
CH >> OUT10
CH >> OUT11
CH >> OUT12
DEC
RES
INC
SERVO
Out.Swap
Press the INC or DEC button at the right edge of
the display or the arrow keys ( pq ) to the left of the
display screen to increase/decrease the input channel
related transmitter output, for example:
BACK
PHASE 1
TX
TX
TX
TX
1
TX
TX
2
3
4
5
1
CH >>OUT1
CH >>OUT2
CH >>OUT3
CH >>OUT4
CH >>OUT5
CH >>OUT6
TX
TX
TX
TX
7
TX
TX
8
9
10
11
12
CH >>OUT7
CH >>OUT8
CH >>OUT9
CH >>OUT10
CH >>OUT11
CH >>OUT12
DEC
RES
INC
SERVO
Out.Swap
Press the RES button to reset the changed output to
the default mapping.
All modified values will be automatically transmitted
to the related receiver.
Press the BACK button to return to the TX ctl sub-
menu.
Notice
If for example you entered "2AILE" in the basic
settings for a fixed-wing model, the transmitter
assigns control function 2 (aileron) to control
channels 2+5 for the left and right aileron. The corre-
sponding transmitter outputs (= receiver inputs) to be
mapped would in this case be channels 2+5 (see the
examples below).
70 Base menu - Transmitter setting