HP ProCurve 5400zl User Manual

■ rip -- Enable/disable/configure Routing Internet Protocol (RIP) on the VLAN interface (p. 274)
■ all -- Process the request for all IP addresses. (p. 219)
■ authentication-key -- Set RIP authentication key (maximum 16 characters). (p. 223)
■ auth-key-text -- Set RIP authentication key (maximum 16 characters). (OCTET-STR)
(p. 225)
■ authentication-type < none | text > -- Set authentication type used on this interface.
(p. 224)
■ metric < 1 to 15 > -- Set metric for this interface. (p. 250)
■ poison-reverse -- Enable/disable poison reverse on this interface. (p. 262)
■ receive < V1-only | V2-only | V1-or-V2 | ... > -- Define RIP version for incoming packets.
(p. 273)
■ rip-compatible < V1-only | V2-only | V1-or-V2 > -- Define RIP version for incoming
and outgoing packets. (p. 274)
■ send < disabled | V1-only | V1-compatible-V2 | ... > -- Define RIP version for outgoing
packets. (p. 275)
■ authentication-key -- Set RIP authentication key (maximum 16 characters). (p. 223)
■ auth-key-text -- Set RIP authentication key (maximum 16 characters). (OCTET-STR)
(p. 225)
■ authentication-type < none | text > -- Set authentication type used on this interface. (p.
224)
■ ip-addr -- Specify the IP address the request is for. (IP-ADDR) (p. 241)
■ authentication-key -- Set RIP authentication key (maximum 16 characters). (p. 223)
■ auth-key-text -- Set RIP authentication key (maximum 16 characters). (OCTET-STR)
(p. 225)
■ authentication-type < none | text > -- Set authentication type used on this interface.
(p. 224)
■ metric < 1 to 15 > -- Set metric for this interface. (p. 250)
■ poison-reverse -- Enable/disable poison reverse on this interface. (p. 262)
■ receive < V1-only | V2-only | V1-or-V2 | ... > -- Define RIP version for incoming packets.
(p. 273)
■ rip-compatible < V1-only | V2-only | V1-or-V2 > -- Define RIP version for incoming
and outgoing packets. (p. 274)
■ send < disabled | V1-only | V1-compatible-V2 | ... > -- Define RIP version for outgoing
packets. (p. 275)
■ metric < 1 to 15 > -- Set metric for this interface. (p. 250)
■ poison-reverse -- Enable/disable poison reverse on this interface. (p. 262)
■ receive < V1-only | V2-only | V1-or-V2 | ... > -- Define RIP version for incoming packets.
(p. 273)
■ rip-compatible < V1-only | V2-only | V1-or-V2 > -- Define RIP version for incoming and
outgoing packets. (p. 274)
■ send < disabled | V1-only | V1-compatible-V2 | ... > -- Define RIP version for outgoing
packets. (p. 275)
■ ip-recv-mac-address -- Associates a L3-mac-address with a VLAN (p. 243)
■ mac-address -- The L3-mac-address to be associated with a VLAN. (MAC-ADDR) (p. 249)
■ interval -- Specify the L3-Mac-Address timeout interval. (p. 240)
■ timer-interval < 1 to 255 > -- Timeout interval in seconds <1-255>. (p. 278)
■ ipv6 -- Configure various IP parameters for the VLAN (p. 244)
■ access-group -- Apply a IPV6 ACl on a VLAN (ASCII-STR) (p. 214)
■ vlan -- VLAN acl. (p. 282)
■ address -- Set IPv6 parameters for communication within an IP network (p. 216)
■ autoconfig -- Automatic address configuration. (p. 225)
■ dhcp -- Configure a DHCPv6 client. (p. 230)
■ full -- Obtain IPv6 address & Configuration information from DHCPv6 server. (p. 235)
211© 2009 Hewlett-Packard Development Company, L.P.
interfaceCommand Line Interface Reference Guide

HP ProCurve 5400zl Specifications

General

Brand	HP
Model	ProCurve 5400zl
Category	Switch
Language	English