HP ProCurve 5400zl User Manual

chain-name -- Specify key chain to use for MD5 authentication. (ASCII-STR) (p.
228)
■
■ passive -- Configures an ospf interface as passive. (p. 258)
■ priority < 0 to 255 > -- Set priority of this router as a designated router. (p. 265)
■ retransmit-interval < 1 to 3600 > -- Set retransmit interval in seconds; the default is
5. (p. 273)
■ transit-delay < 1 to 3600 > -- Set transit delay in seconds; the default is 1. (p. 279)
■ md5-auth-key-chain -- Set MD5 authentication method and key chain. (p. 250)
■ chain-name -- Specify key chain to use for MD5 authentication. (ASCII-STR) (p. 228)
■ passive -- Configures an ospf interface as passive. (p. 258)
■ priority < 0 to 255 > -- Set priority of this router as a designated router. (p. 265)
■ retransmit-interval < 1 to 3600 > -- Set retransmit interval in seconds; the default is 5.
(p. 273)
■ transit-delay < 1 to 3600 > -- Set transit delay in seconds; the default is 1. (p. 279)
■ pim-dense -- Enable/disable/configure PIM-DM protocol on the VLAN interface (p. 259)
■ graft-retry-interval < 1 to 10 > -- Set the interval a PIM router waits for a Graft Ack before
resending a Graft on this interface (p. 235)
■ hello-delay < 0 to 5 > -- Set the maximum time before a triggered PIM Hello message
is transmitted on this interface (p. 236)
■ hello-interval < 5 to 300 > -- Set the frequency at which PIM Hello messages are
transmitted on this interface (p. 236)
■ ip-addr -- Set the source IP address for the PIM-DM packets sent out on this interface (p.
241)
■ any -- Dynamically determine IP address. (p. 221)
■ ip-addr -- Specify IP address. (IP-ADDR) (p. 241)
■ lan-prune-delay -- Turn on/off the LAN Prune Delay Option on this interface (p. 247)
■ max-graft-retries < 1 to 10 > -- Set the maximum number of times this router will resend
a Graft on this interface (p. 249)
■ override-interval < 500 to 6000 > -- Set the value inserted into the Override Interval field
of a LAN Prune Delay option on this interface (p. 258)
■ propagation-delay < 250 to 2000 > -- Set the value inserted into the LAN Prune Delay
field of a LAN Prune Delay option on this interface (p. 266)
■ ttl-threshold < 0 to 255 > -- Set the Time To Live in a PIM-DM State Refresh message
at which it is not forwarded on this interface (p. 279)
■ pim-sparse -- Enable/disable/configure PIM-SM protocol on the VLAN interface (p. 259)
■ dr-priority -- Set the priority value to use on the interface in the Designated Router
election process (p. 231)
■ hello-delay < 0 to 5 > -- Set the maximum time before a triggered PIM Hello message
is transmitted on this interface (p. 236)
■ hello-interval < 5 to 300 > -- Set the frequency at which PIM Hello messages are
transmitted on this interface (p. 236)
■ ip-addr -- Set the source IP address for the PIM-SM packets sent out on this interface (p.
241)
■ any -- Dynamically determine IP address. (p. 221)
■ ip-addr -- Specify IP address. (IP-ADDR) (p. 241)
■ lan-prune-delay -- Turn on/off the LAN Prune Delay Option on this interface (p. 247)
■ nbr-timeout < 60 to 8000 > -- Set the neighbour loss time interval for this interface (p.
255)
■ override-interval < 500 to 6000 > -- Set the value inserted into the Override Interval field
of a LAN Prune Delay option on this interface (p. 258)
■ propagation-delay < 250 to 2000 > -- Set the value inserted into the LAN Prune Delay
field of a LAN Prune Delay option on this interface (p. 266)
■ proxy-arp -- Enable/disable proxy ARP (p. 268)
210© 2009 Hewlett-Packard Development Company, L.P.
interfaceCommand Line Interface Reference Guide

HP ProCurve 5400zl Specifications

General

Brand	HP
Model	ProCurve 5400zl
Category	Switch
Language	English