HP ProCurve 5400zl User Manual

■ server-address -- Configure DNS server IP address. (p. 308)
■ priority < 1 to 2 > -- Priority of Server Address. (NUMBER) (p. 305)
■ ip6addr -- DNS server IPv6 address. (IPV6-ADDR) (p. 302)
■ ipaddr -- DNS server IP address. (IP-ADDR) (p. 302)
■ [no] ip icmp -- Configure ICMP Rate Limiting capacity (p. 300)
■ addrmask -- Enable/disable address mask replies (p. 294)
■ burst-normal < 0 to 1000000 > -- The maximum number of icmp replies to send per second
(p. 296)
■ echo -- Enable/disable echo replies to broadcast echo requests (p. 299)
■ broadcast-request < Min | Max > -- Enable/disable echo replies to broadcast echo requests
(p. 296)
■ redirects -- Enable/disable redirect error messages (p. 306)
■ reply-limit -- Enable/disable ICMP reply rate limiting (p. 306)
■ unreachable -- Enable/disable destination unreachable error messages (p. 312)
■ [no] ip igmp -- Enable/disable/configure IP Multicast Group Protocol (IGMP) feature (p. 300)
■ auto -- Instruct the device to monitor incoming multicast traffic on the specified ports (this is
the default behavior) ([ethernet] PORT-LIST) (p. 296)
■ blocked -- Instruct the device to drop incoming multicast packets received on the specified
ports ([ethernet] PORT-LIST) (p. 296)
■ fastleave -- Enables or disables IGMP Fast Leaves ([ethernet] PORT-LIST) (p. 299)
■ forcedfastleave -- When enabled, this feature forces IGMP Fast Leaves to occur even when the
port is cascaded ([ethernet] PORT-LIST) (p. 299)
■ forward -- Instruct the device to forward incoming multicast packets received on the specified
ports ([ethernet] PORT-LIST) (p. 300)
■ high-priority-forward -- Enable/disable the high priority forwarding of traffic for subscribed IP
Multicast groups (p. 300)
■ querier -- Specify querier/non-querier capability for the VLAN (p. 306)
■ interval < 5 to 300 > -- Sets the interval in seconds between IGMP queries (default: 125) (p.
301)
■ [no] ip irdp -- Enable/disable ICMP Router Discovery Protocol (IRDP) (p. 303)
■ [no] ip load-sharing -- Specify the maximum number of equal cost IP load sharing paths (p. 303)
■ load-sharing-value < 2 to 4 > -- Specify the maximum number of equal cost IP load sharing
paths (p. 303)
■ [no] ip multicast-routing -- Enable/disable IP multicast routing on the device (p. 304)
■ ip preserve -- (p. 305)
■ [no] ip route -- Add or delete static routing table entries (p. 307)
■ ip-addr -- Specify IP address and mask of the route destination. (IP-ADDR/MASK-LENGTH) (p.
302)
■ blackhole -- Specify that packets are silently discarded with no ICMP message sent. (p. 296)
■ distance < 1 to 255 > -- Set the administrative distance to associate with this static route.
(p. 298)
■ ip-addr -- Specify gateway IP address. (IP-ADDR) (p. 302)
■ distance < 1 to 255 > -- Set the administrative distance to associate with this static route.
(p. 298)
■ reject -- Specify that packets are discarded and ICMP error is returned to sender. (p. 306)
■ distance < 1 to 255 > -- Set the administrative distance to associate with this static route.
(p. 298)
■ vlan -- Specify the destination VLAN. (VLAN-ID) (p. 312)
■ distance < 1 to 255 > -- Set the administrative distance to associate with this static route.
(p. 298)
■ [no] ip router-id -- Define the device router id (p. 307)
■ ipaddr -- Define the device router id (IP-ADDR) (p. 302)
■ [no] ip routing -- Enable/disable IP routing support on the device (p. 308)
291© 2009 Hewlett-Packard Development Company, L.P.
ipCommand Line Interface Reference Guide

HP ProCurve 5400zl Specifications

General

Brand	HP
Model	ProCurve 5400zl
Category	Switch
Language	English