HP ProCurve 5400zl User Manual

■ receive < V1-only | V2-only | V1-or-V2 | ... > -- Define RIP version for incoming packets.
(p. 745)
■ rip-compatible < V1-only | V2-only | V1-or-V2 > -- Define RIP version for incoming and
outgoing packets. (p. 747)
■ send < disabled | V1-only | V1-compatible-V2 | ... > -- Define RIP version for outgoing
packets. (p. 747)
■ metric < 1 to 15 > -- Set metric for this interface. (p. 734)
■ poison-reverse -- Enable/disable poison reverse on this interface. (p. 741)
■ receive < V1-only | V2-only | V1-or-V2 | ... > -- Define RIP version for incoming packets. (p.
745)
■ rip-compatible < V1-only | V2-only | V1-or-V2 > -- Define RIP version for incoming and
outgoing packets. (p. 747)
■ send < disabled | V1-only | V1-compatible-V2 | ... > -- Define RIP version for outgoing
packets. (p. 747)
■ [no] vlan VLAN-ID ip-recv-mac-address -- Associates a L3-mac-address with a VLAN (p. 731)
■ mac-address -- The L3-mac-address to be associated with a VLAN. (MAC-ADDR) (p. 733)
■ interval -- Specify the L3-Mac-Address timeout interval. (p. 728)
■ timer-interval < 1 to 255 > -- Timeout interval in seconds <1-255>. (p. 748)
■ vlan VLAN-ID ipv6 -- Configure various IP parameters for the VLAN (p. 731)
■ access-group -- Apply a IPV6 ACl on a VLAN (ASCII-STR) (p. 713)
■ vlan -- VLAN acl. (p. 750)
■ address -- Set IPv6 parameters for communication within an IP network (p. 713)
■ autoconfig -- Automatic address configuration. (p. 719)
■ dhcp -- Configure a DHCPv6 client. (p. 722)
■ full -- Obtain IPv6 address & Configuration information from DHCPv6 server. (p. 725)
■ rapid-commit -- Obtain IPv6 address quickly from DHCPv6 server. (p. 745)
■ ipv6-addr -- Configure a link-local IPv6 address. (IPV6-ADDR) (p. 731)
■ link-local -- Configure a link-local IPv6 address. (p. 733)
■ ipv6-addr/mask -- Configure IPv6 address represented in CIDR notation.
(IPV6-ADDR/PREFIX-LEN) (p. 732)
■ anycast -- Address that is assigned to a set of interfaces that typically belong to different
nodes (p. 716)
■ eui-64 -- An IPv6 EUI-64 address that can be automatically configured on any interface
(p. 723)
■ enable -- Enable IPv6 on an interface and configures an automatically generated link-local addr.
(p. 723)
■ mld -- Enable/disable/configure IPv6 Multicast Listener Discovery (MLD) feature on a VLAN (p.
735)
■ auto -- Instruct the device to monitor incoming multicast traffic on the specified ports (this
is the default behavior) ([ethernet] PORT-LIST) (p. 719)
■ blocked -- Instruct the device to drop incoming multicast packets received on the specified
ports ([ethernet] PORT-LIST) (p. 720)
■ fastleave -- Enables MLD fast-leaves on the specified ports in the selected VLAN ([ethernet]
PORT-LIST) (p. 723)
■ forcedfastleave -- Enables MLD Forced Fast-Leave on the specified ports in the selected
VLAN, even if they are cascaded ([ethernet] PORT-LIST) (p. 724)
■ forward -- Instruct the device to forward incoming multicast packets received on the specified
ports ([ethernet] PORT-LIST) (p. 724)
■ querier -- This command disables or re-enables the ability for the switch to become querier
if necessary (p. 744)
■ nd -- IPv6 nodes on the same link use Neighbor Discovery to discover each other's presence,
link-layer addresses, routers and to maintain reachability information about the paths to active
neighbors (p. 737)
710© 2009 Hewlett-Packard Development Company, L.P.
vlanCommand Line Interface Reference Guide

HP ProCurve 5400zl Specifications

General

Brand	HP
Model	ProCurve 5400zl
Category	Switch
Language	English