HP ProCurve 5400zl User Manual

ns-interval -- Configures the neighbor discovery time between neighbor solicitation requests
sent for an unresolved destination, or between duplicate address detection neighbor
solicitation requests (p. 737)
■
■ number < 1000 to 3600000 > -- Configures the neighbor discovery time between neighbor
solicitation requests sent for an unresolved destination, or between duplicate address
detection neighbor solicitation requests (p. 738)
■ reachable-time -- Configures the length of time neighbors are considered reachable after
being confirmed as reachable via the neighbor unreachability detection algorithm (p. 745)
■ number < 1000 to 3600000 > -- Configures the router lifetime sent in router
advertisements (p. 738)
■ [no] vlan VLAN-ID jumbo -- Labels this VLAN as a Jumbo VLAN, allowing you to pass packets up
to 9220 bytes in size (p. 732)
■ [no] vlan VLAN-ID monitor -- Define either the VLAN is to be monitored or not (p. 736)
■ all < In | Out | Both > -- Monitor all traffic. (p. 715)
■ mirror -- Mirror destination. (p. 735)
■ mirror_session_name -- Mirror destination name. (p. 735)
■ monitor_mirror_session_id < 1 to 4 > -- Mirror destination number. (p. 736)
■ vlan VLAN-ID name -- Set the VLAN's name (ASCII-STR) (p. 737)
■ vlan VLAN-ID protocol -- Set a predefined protocol for the current VLAN. (p. 743)
■ protocol-group -- Enter a list of protocols for the current VLAN delimited by commas.
(ASCII-STR) (p. 743)
■ protocols < IPX | IPv4 | IPv6 | ... > -- Set a predefined protocol for the current VLAN. (p. 744)
■ [no] vlan VLAN-ID qos -- Set VLAN-based priority (p. 744)
■ dscp -- Specify DSCP policy to use. (p. 722)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p. 720)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 728)
■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP
(Differentiated-Services Codepoint) value and an 802 (p. 752)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 742)
■ [no] vlan VLAN-ID service-policy -- Apply the QoS/Mirror policy on the vlan (ASCII-STR) (p. 748)
■ in -- Apply policy on inbound packets. (p. 728)
■ [no] vlan VLAN-ID tagged -- Assign ports to current VLAN as tagged ([ethernet] PORT-LIST) (p.
748)
■ [no] vlan VLAN-ID untagged -- Assign ports to current VLAN as untagged ([ethernet] PORT-LIST)
(p. 750)
■ [no] vlan VLAN-ID voice -- Labels this VLAN as a Voice VLAN, allowing you to separate, prioritize,
and authenticate voice traffic moving through your network (p. 750)
■ [no] vlan VLAN-ID vrrp -- Enable/disable/configure VRRP operation on the VLAN (p. 751)
■ vrid < 1 to 255 > -- Configure a virtual router instance for the VLAN (p. 751)
■ advertise-interval < 1 to 255 > -- Set time interval (in seconds) between sending VRRP
advertisement messages (p. 715)
■ backup -- Designate the virtual router instance as a Backup (p. 720)
■ enable -- Enable/disable operation of the virtual router instance (p. 723)
■ failback -- Trigger VR to failback to its configured priority value (p. 723)
■ failover -- Trigger VR to failover to a peer (p. 723)
■ with-monitoring -- Trigger VR to failover and continue montior of master VR (p. 753)
■ owner -- Designate the virtual router instance as an Owner (Master) (p. 739)
■ preempt-delay-time < 1 to 600 > -- Enable the pre-emptive delay timer for the virtual router
instance (p. 741)
■ preempt-mode -- Enable/disable preempt mode for the virtual router instance (p. 742)
■ primary-ip-address -- Specify IP address the virtual router instance will use as a source in
VRRP advertisement messages (p. 742)
■ ip-addr -- Specify IP address. (IP-ADDR) (p. 729)
711© 2009 Hewlett-Packard Development Company, L.P.
vlanCommand Line Interface Reference Guide

HP ProCurve 5400zl Specifications

General

Brand	HP
Model	ProCurve 5400zl
Category	Switch
Language	English