HPE FlexNetwork 5510 HI Series Layer 3 - Ip Routing Configuration Guide

95
Step Command Remarks
2. Configure the
source IP address
of BFD echo
packets.
bfd echo-source-ip
ip-address
By default, the source IP
address of BFD echo packets
is not configured.
3. Enter interface
view.
interface
interface-type interface-number N/A
4. Enable BFD for
OSPF FRR.
ospf primary-path-detect bfd echo
By default, BFD for OSPF
FRR is disabled.
Displaying and maintaining OSPF
Execute display commands in any view and reset commands in user view.
Task Command
Display OSPF process
information.
display ospf
[ process-id ] [
verbose
] [
standby slot
slot-number ]
Display OSPF GR information.
display ospf
[ process-id ]
graceful-restart
[
verbose
]
Display OSPF FRR backup next
hop information.
display ospf
[ process-id ] [
area
area-id ]
fast-reroute lfa-candidate
Display OSPF LSDB information.
display ospf
[ process-id ]
lsdb
[
area
area-id |
brief
| [ {
asbr
|
ase
|
network
|
nssa
|
opaque-area
|
opaque-as
|
opaque-link
|
router
|
summary
} [ link-state-id ] ] [
originate-router
advertising-router-id |
self-originate
] ]
Display OSPF next hop
information.
display ospf
[ process-id ]
nexthop
Display OSPF neighbor
information.
display ospf
[ process-id ]
peer
[
verbose
] [ interface-type
interface-number ] [ neighbor-id ]
Display neighbor statistics for
OSPF areas.
display ospf
[ process-id ]
peer statistics
Display OSPF routing table
information.
display ospf
[ process-id ]
routing
[ ip-address { mask-length | mask } ]
[
interface
interface-type interface-number ] [
nexthop
nexthop-address ] [
verbose
]
Display OSPF topology
information.
display ospf
[ process-id ] [
area
area-id ]
spf-tree
[
verbose
]
Display OSPF statistics.
display ospf
[ process-id ]
statistics
[
error
|
packet
[ interface-type
interface-number ] ]
Display OSPF virtual link
information.
display ospf
[ process-id ]
vlink
Display OSPF request queue
information.
display ospf
[ process-id ]
request-queue
[ interface-type
interface-number ] [ neighbor-id ]
Display OSPF retransmission
queue information.
display ospf
[ process-id ]
retrans-queue
[ interface-type
interface-number ] [ neighbor-id ]
Display OSPF ABR and ASBR
information.
display ospf
[ process-id ]
abr-asbr
[
verbose
]
Display summary route
information on the OSPF ABR.
display ospf
[ process-id ] [
area
area-id ]
abr-summary
[ ip-address
{ mask-length | mask } ] [
verbose
]

HPE FlexNetwork 5510 HI Series Specifications

General

Model	HPE FlexNetwork 5510 HI Series
Category	Switch
Switch Type	Managed
Fans	Redundant fans
Layer	Layer 3
IPv6 Support	Yes
Warranty	Limited lifetime warranty
Power over Ethernet (PoE)	Available on some models (PoE+)
MAC Address Table Size	32, 000 entries
Routing Protocol	RIP, OSPF, BGP, IS-IS, Static Routing
Management	CLI, Web, SNMP
Operating Temperature	0°C to 45°C
Dimensions	440 x 400 x 44 mm
Input Voltage	100-240 VAC, 50/60 Hz
Memory and Processor	1 GB RAM, 1 GHz CPU
Operating Humidity	5% to 95% (non-condensing)
Security Features	ACL, 802.1X, RADIUS, TACACS+, SSH, SSL