d
Preparing for Motorized Sectioning (DM only) ................................................................................... 2-26
Preparing for Sectioning ............................................................................................................... 2-26
Selecting an Motorized Sectioning Mode ..................................................................................... 2-26
Moving the Specimen Head to the Sectioning Start Position ........................................................ 2-27
Cutting the Specimen to Flat Surface (Rough Shaving) in the TRIM Mode .................................. 2-27
Checking the Section Thickness................................................................................................... 2-27
Sectioning Automatically (DM only) .................................................................................................... 2-28
How to Operate the Right Panel ................................................................................................... 2-28
How to Operate the Foot Switch ................................................................................................... 2-28
Adjusting the Anti-Roll Plate ............................................................................................................... 2-29
Adjusting the Forward/Backward Position of the Anti-Roll Plate ................................................... 2-29
Adjusting the Angle (Lateral Inclination) of the Anti-Roll Plate ...................................................... 2-29
Adjusting the Blade Holder ................................................................................................................. 2-30
Adjusting the Blade Angle (Relief Angle) ...................................................................................... 2-31
Removing the Blade Holder from the Chamber ............................................................................ 2-32
Setting the Blade Holder in the Chamber (Normal) ...................................................................... 2-32
Setting the Blade Holder in the Chamber (Cryo3 Adapter Is Used) .............................................. 2-33
Turning on the Chamber LED Lights .................................................................................................. 2-34
Assisting with Vacuum ....................................................................................................................... 2-34
Draft Generator .................................................................................................................................. 2-35
Starting the Draft Generator ......................................................................................................... 2-35
Stopping the Draft Generator ........................................................................................................ 2-35
Changing the Suction Force of the Draft Generator ..................................................................... 2-35
Setting the Parking Plate .................................................................................................................. 2-36
Setting the Heat Extractor .................................................................................................................. 2-36
Plastic Object Holder .......................................................................................................................... 2-37
Using the Plastic Object Holder .................................................................................................... 2-37
Adapter for Cryo3 Object Holder ........................................................................................................ 2-38
Using Adapter for Cryo3 Object Holder ........................................................................................ 2-38
Freeze the Block Using the PINO Hyfluid Method ............................................................................. 2-38
Chapter 3 Maintenance/Inspection
Daily Care and Inspection ............................................................................ 3-1
Cleaning the Chamber ......................................................................................................................... 3-1
Cleaning the Chamber .................................................................................................................... 3-1
Cleaning the Chamber Drain Pipe .................................................................................................. 3-1
Cleaning the Specimen Head ............................................................................................................... 3-1
Cleaning the Holder Installation Position ........................................................................................ 3-1
Cleaning the Operation Panel and Instrument Exterior ........................................................................ 3-1
Setting the Waste Tank ........................................................................................................................ 3-2
Cleaning the Waste Tank ..................................................................................................................... 3-2
How to Install the Vacuum Filter Set .................................................................................................... 3-3
Replacing the Vacuum Filter Set .......................................................................................................... 3-4
Cleaning the Vacuum Hose ............................................................................................................ 3-4
How to Set the Draft Generator ............................................................................................................ 3-5
Draft Generator Error Codes ................................................................................................................ 3-5
Replacing the Draft Generator Filter .................................................................................................... 3-6
How to Disassemble/Set and Clean the Blade Holder ......................................................................... 3-7
Disassembling/Cleaning the Blade Holder ..................................................................................... 3-7
Disassembling/Cleaning the Stage ................................................................................................. 3-8
Disassembling/Cleaning the Wave Washer and Lever Locking Bracket of the Blade Holder (Base)
....................................................................................................................................................... 3-8
How to Disassemble/Set and Clean the Anti-Roll Plate ....................................................................... 3-9
How to Remove the Anti-Roll Plate and Vacuum Suction Port ....................................................... 3-9
How to Remove Only the Anti-Roll Plate ........................................................................................ 3-9
How to Install the Anti-Roll Plate .................................................................................................... 3-9
Disassembling and Assembling the Anti-Roll Plate ...................................................................... 3-10
Replacing the Glass of the Anti-Roll Plate .................................................................................... 3-10
To Next Page
Loading...
Need help?
General
