Schweitzer Engineering Laboratories SEL-787 - Page 16

xiv List of Figures
SEL-787 Relay Instruction Manual Date Code 20081022
Figure 8.4 Front-Panel Pushbuttons.............................................................................................................8.4
Figure 8.5 Main Menu .................................................................................................................................8.5
Figure 8.6 MAIN Menu and METER Submenu ......................................................................................... 8.6
Figure 8.7 METER Menu and ENERGY Submenu....................................................................................8.6
Figure 8.8 Relay Response When Demand, Peak Demand, Energy, or Max/Min Metering Is Reset.........8.6
Figure 8.9 Relay Response When No Analog Cards Are Installed.............................................................8.6
Figure 8.10 Relay Response When No Math Variables Enabled ..................................................................8.7
Figure 8.11 MAIN Menu and EVENTS Submenu........................................................................................8.7
Figure 8.12 EVENTS Menu and DISPLAY Submenu.................................................................................. 8.7
Figure 8.13 Relay Response When No Event Data Available.......................................................................8.7
Figure 8.14 Relay Response When Events Are Cleared ...............................................................................8.7
Figure 8.15 MAIN Menu and TARGETS Submenu .....................................................................................8.8
Figure 8.16 TARGETS Menu Navigation ..................................................................................................... 8.8
Figure 8.17 MAIN Menu and CONTROL Submenu ....................................................................................8.8
Figure 8.18 CONTROL Menu and OUTPUTS Submenu ............................................................................. 8.9
Figure 8.19 CONTROL Menu and LOCAL BITS Submenu ........................................................................8.9
Figure 8.20 MAIN Menu and SET/SHOW Submenu .................................................................................8.10
Figure 8.21 SET/SHOW Menu ...................................................................................................................8.11
Figure 8.22 MAIN Menu and Status Submenu ...........................................................................................8.12
Figure 8.23 Factory Default Front-Panel LEDs...........................................................................................8.12
Figure 8.24 Target Reset Pushbutton ...........................................................................................................8.13
Figure 8.25 Operator Control Pushbuttons and LEDs .................................................................................8.14
Figure 9.1 Example Event Summary...........................................................................................................9.3
Figure 9.2 Sample Event History.................................................................................................................9.5
Figure 9.3 Example Standard 15-Cycle Analog Event Report 1/4-Cycle Resolution ..............................9.11
Figure 9.4 Derivation of Analog Event Report Current Values and RMS Current Values From
Sampled Current Waveform ................................................................................................9.12
Figure 9.5 Derivation of Phasor RMS Current Values From Event Report Current Values......................9.13
Figure 9.6 Example Standard 15-cycle Digital Event Report (EVE D Command)
1/4 Cycle Resolution ...........................................................................................................9.18
Figure 9.7 Example Standard 15-cycle Differential Event Report (EVE DIF1 Command)
1/4 Cycle Resolution ...........................................................................................................9.21
Figure 9.8 Example Sequential Events Recorder (SER) Event Report .....................................................9.22
Figure 10.1 Low-Level Test Interface (J2 and J3) .......................................................................................10.2
Figure 10.2 Three-Phase Wye AC Connections ..........................................................................................10.5
Figure 10.3 Three-Phase Open-Delta AC Connections...............................................................................10.5
Figure 10.4 CTR1 Current Source Connections..........................................................................................10.7
Figure 10.5 CTR2 Current Source Connections..........................................................................................10.8
Figure 10.6 Wye Voltage Source Connections ............................................................................................10.9
Figure 10.7 Delta Voltage Source Connections .........................................................................................10.10
Figure B.1 Firmware File Transfer Process ................................................................................................ B.2
Figure C.1 SEL Communications Processor Star Integration Network ...................................................... C.3
Figure C.2 Multitiered SEL Communications Processor Architecture ....................................................... C.4
Figure C.3 Enhancing Multidrop Networks With SEL Communications Processors................................. C.6
Figure C.4 Example of SEL Relay and SEL Communications Processor Configuration........................... C.7
Figure D.1 Application Confirmation Timing With URETRY n = 2 .......................................................... D.7
Figure D.2 Message Transmission Timing.................................................................................................. D.8
Figure D.3 Sample Response to SHO DNP Command............................................................................. D.13
Figure D.4 Port MAP Command ............................................................................................................... D.14
Figure D.5 Sample Custom DNP3 AI Map Settings ................................................................................. D.16
Figure D.6 Analog Input Map Entry in
ACSELERATOR QuickSet Software............................................. D.17
Figure D.7 AI Point Label, Scaling and Deadband in
ACSELERATOR QuickSet Software ...................... D.17
Figure D.8 Sample Custom DNP3 BO Map Settings................................................................................D.18
Figure D.9 Binary Output Map Entry in
ACSELERATOR QuickSet Software ........................................... D.18
Figure F.1 SEL-787 Predefined Reports...................................................................................................... F.6
Figure F.2 SEL-787 Datasets....................................................................................................................... F.8
Figure F.3 Goose Quality............................................................................................................................. F.9