Schweitzer Engineering Laboratories SEL-787 - Page 555

IN.3Index
J–R
Date Code 20081022 Instruction Manual SEL-787 Relay
physical location 2.1
power supply 1.4
, 2.15
rack mounting accessory 1.3
See also Commissioning Tests
Instantaneous Overcurrent Elements
See Overcurrent Elements
Instruction Manual Versions A.2
IRIG-B Time
Synchronization 7.4
, 7.23
input specifications 1.9
IRI command 7.23
via communications processor C.3
J
Jumpers 2.9
analog card (V or I) 2.9
analog card configuration 2.10
breaker control jumper 2.11
Password 2.11
SEL
BOOT JUMPER 2.11
L
Labels
configurable 1.3
, 8.12
Latch Bits 4.72
nonvolatile state 4.73
LCD
See Front Panel
LED Settings 4.105
Pushbutton LEDs 4.105
Target LEDs 4.105
Load Profiling 5.11
Local Bits 4.103
NLB, CLB, SLB, PLB 4.103
Logic Settings
output contacts 4.81
Loss of Potential (LOP) 4.61
Low-Level Test Interface 10.2
M
Maintenance 10.11
routine checks 10.11
self testing 10.11
Menus
See Front Panel, menus
Meter 5.3
accuracy 1.12
analog input 5.9
current 5.2
, 5.3, 5.4
demand 5.9
differential 5.4
energy 5.6
frequency 5.4
fundamental 5.3
harmonic 5.10
math variable 5.8
minimum/maximjum 5.6
negative sequence 5.4
peak demand 5.9
power factor 5.2
reactive power 5.2
, 5.3
real power 5.2
rms 5.8
RTD 5.5
RTD temperatures 5.5
synchrophasor 5.11
, H.10
temperature 5.5
thermal 5.5
voltage 5.3
, 5.4
METER PM Command
Phasor Measurement and Control
Unit H.10
MIRRORED BITS I.1–I.6
Modbus E.1
03h read holding registers E.8
04h input holding registers E.8
06h preset single register E.12
10h preset multiple registers E.12
60h read parameter E.13
61h read parameter text E.15
62h read enumeration text E.15
7Dh encapsulated packet E.16
7Eh NOP (no operation) E.17
contact outputs E.17
cyclical redundancy check E.3
exception responses E.3
function codes E.2
history data E.22
Modbus Map Settings 4.110
Modbus Register Map E.22
password protection E.17
protocol description E.1
protocol setting 4.94
query E.2
relay settings E.17
response E.2
settings 4.94
N
Network Parameters 3.3
Nonisolated EIA-232 Serial Port 2.5
O
Overcurrent Elements 4.31
adaptive overcurrent element 4.32
logic diagram 4.32
negative-sequence 4.33
, 4.35
neutral 4.36
residual 4.33
, 4.34
Overvoltage Elements 4.51
logic diagram 4.52
, 4.53
P
Password
access level 7.13
–7.14
change 7.28
factory default 7.27
front panel 8.3
jumper 2.11
Phase Overcurrent Elements
See Overcurrent Elements
Phase Rotation 4.82
phasor diagram 4.83
setting, PHROT 4.82
Port Settings (SET P Command) 4.92
Power
functional test 10.8
meter 5.3
power measurement
convention 5.2
Power Factor
functional test 10.8
meter 5.3
power factor measurement
convention 5.2
Power Supply
fuse ratings 2.26
Pushbuttons 8.1
–8.4, 8.13
navigation 8.4
target reset 8.13
, 8.14
R
Rack Mounting Accessory 1.3
Reactive
power measurement
convention 5.2
Reactive Power 5.2
meter 5.3
Real Power 5.2
meter 5.3
See also Meter
Rear Panel 2.13
Rear-Panel Connections 2.12
Relay Word Bits J.1
row list J.4
Remote Trip 4.68
control input 4.70
Replacement Rear Connector Kit 1.3
Report Settings 4.106
Event report 4.108
SER trigger 4.107
Reset
targets 8.13
Resistance Temperature Device (RTD)
alarm temperatures 4.50
failure messages 5.5
location settings 4.49
status messages 5.5
temperature vs. resistance 4.50
trip temperatures 4.50
See also Meter
Restricted Earth Fault (REF)
Element 4.27
Retrieve
event 3.11
Rotating Display 4.103
RTD
See Resistance Temperature Device