Schweitzer Engineering Laboratories SEL-787 - Page 556

IN.4 Index
S–Z
SEL-787 Relay Instruction Manual Date Code 20081022
S
Safety Information
Laser/LED Emitter xx
symbols xix
SEL ASCII Protocol 7.10, C.1
SEL Binary Protocol C.2
SEL Communications
Processor C.3
–C.10
SEL-2600 Series RTD Module 1.2
failure messages 5.5
fiber-optic connection 2.16
RTD-based protection 4.49
SEL-3306
See Synchrophasors
SEL-787 Relay
cleaning chassis xxii
features 1.1
options 1.2
SELBOOT 2.11
Self Tests 10.11
See also Status, Relay
self-test table 10.12
SELOGIC Control Equations 4.74
circuit breaker auxiliary 4.70
contact output 4.81
counters 4.79
event trigger 9.2
operators 4.74
–4.78
PMU trigger H.8
Relay Word bits J.1
timers 4.78
trip logic 4.68
Sequential Events Recorder
(SER) 7.29
, 9.21
clearing 9.21
example report 9.22
retrieving reports 9.21
trigger settings 4.107
, 9.21
SER (Sequential Events Recorder)
automatic deletion and
reinsertion 4.106
SER D Command 7.30
SER, See Sequential Events Recorder
(SER)
SET Command 7.30
Set Relay
editing keystrokes 6.5
serial communications
port 6.4
–6.5
settings sheets SET..1
using front panel 6.2
Setting 6.1
calculation method 4.2
classes 6.1
error messages 6.6
front panel 6.2
instances 6.1
serial communications
port 6.4
–6.5
settings sheets SET..1
Settings 4.2–4.110
analog input example 4.86
DNP Map Settings (SET DNP
Command) 4.109
Front-Panel Set (SET F
Command) 4.96
–4.105
Global Settings (SET G
Command) 4.82
–4.92
Group Settings (SET
Command) 4.2
–4.90
Logic Settings (SET L
Command) 4.72
Modbus Map Settings (SET M
Command) 4.110
Port Settings (SET P
Command) 4.92
Report Settings (SET R
Command) 4.106
Short Circuit Protection
See Overcurrent Elements
Side Panel 2.13
Software (
ACSELERATOR
QuickSet) 3.1
databases 3.4
device editor 3.8
expression builder 3.9
Human Machine Interface
(HMI) 3.12
settings editor 3.6
Specifications 1.8
–1.12
Status, Relay 7.34
–7.35
serial communication port 1.6
DeviceNet status 1.6
Synchrophasors
MET PM Command H.10
protocols
C37.118 H.11
Relay Word bits H.9
settings H.4
T
Targets 8.12
front-panel function 8.12
reset targets 8.13
view using communications
port 7.36
Temperature
See Resistance Temperature Device
(RTD)
Testing 10.1
–10.14
acceptance testing 10.3
commissioning testing 10.3–10.7
connection tests 10.7
low-level test interface 10.2
maintenance testing 10.11
methods 10.3
, 10.11
relay elements 10.11
self tests 10.11
test connections 10.7
, 10.9
with SER 10.11
with targets, LEDs 10.11
with terminal 10.11
Through-Fault Event Monitor 5.12
Time Code
See IRIG-B Time Synchronization
Transformer Protection
applications 1.4
protection elements 4.1
Trigger
PMU H.8
Trip Contact
See also Contact Outputs
fail-safe operation 2.17
, 4.81
wiring diagram 2.17
Trip Reset
front-panel function 8.13
Trip/Close Logic 4.68
breaker status 52A 4.70
logic diagram 4.69
trip equation TR 4.69
trip Relay Word bit 4.69
trip unlatch ULTRIP 4.70
Troubleshooting 10.14
setting error messages 6.6
Typographic Conventions xviii
U
Undervoltage Elements 4.51
logic diagram 4.52
Upgrade
See Firmware, upgrade instructions
V
Voltages
connections 2.18
delta wiring diagram 2.19
four-wire wye wiring diagram 2.19
input settings
example 4.4
loss of potential 4.61
open-delta wiring diagram 2.19
phase-to-neutral voltage
elements 4.51
phase-to-phase voltage
elements 4.51
See also Meter
Z
Z number 3.7, A.1