Siemens SINAMICS PERFECT HARMONY GH180 - Page 174

Set active con󹪝g 󹪝le Use this pick list to set the displayed 󹪝le to be the active con󹪝guration
󹪝le.
This function overrides what is set in the SOP. Any change in the SOP
is checked against the 󹪝le set in this function. Once a change in the
SOP is detected, that 󹪝le will then be the active 󹪝le. The keypad menu
setting is now ignored. This ensures no unintentional toggling of the
con󹪝guration 󹪝les.
To switch back to the keypad 󹪝le set it by this menu. If no change in the
SOP occurs, the keypad set con󹪝guration 󹪝le will remain in memory.
Setup SOP con󹪝g 󹪞ags Use this submenu for SOP 󹪞ag con󹪝guration.
Create new con󹪝g 󹪝le Use this function to save slave parameters to a 󹪝le name you specify.
Use the drive keypad to enter the 󹪝le name. To get to the alphanu‐
meric characters, use the left or right arrow keys to position the cur‐
sor. Use the up or down arrow keys to scroll to the desired letter or
number.
Set
SOPConfigFileX_O
Use this function to map the name of the 󹪞ag in the SOP
󹪝le, SOPConfigFileX_O (X = 1 to 8) to a name of a slave con󹪝gu‐
ration 󹪝le.
Once the SOP is running, and this 󹪞ag is set to ‘true’, the con󹪝guration
󹪝le will be switched into memory. This is a method of switching
among multiple motors using one drive.
Select the 󹪝le names from a pick list or create new 󹪝les as described.
Table 6-102 Slave Setup and Con󹪝guration Parameters
Parameter ID Units Default Min Max Description
Multiple con󹪝g 󹪝les 9185 O󹪜 Enable multiple con󹪝guration 󹪝le opera‐
tion.
Show active con󹪝g 󹪝le 9195 Display the current active con󹪝guration 󹪝le
on the 󹪞ash disk.
Set active con󹪝g 󹪝le 9196 defaults.sfg Set the displayed 󹪝le to be the active con‐
󹪝guration 󹪝le on the 󹪞ash disk.
Setup SOP con󹪝g 󹪞ags 9186 Submenu Access menu for SOP 󹪞ag con󹪝guration.
Create new con󹪝g 󹪝le 9197 Create a new con󹪝guration 󹪝le using the
numeric keypad.
Set SOPCon󹪝gFile1_O 9187 defaults.sfg Set the name of con󹪝guration 󹪝le 1 to be
used with corresponding SOP 󹪞ag 1.
Set SOPCon󹪝gFile2_O 9188 defaults.sfg Set the name of con󹪝guration 󹪝le 2 to be
used with corresponding SOP 󹪞ag 2.
Set SOPCon󹪝gFile3_O 9189 defaults.sfg Set the name of con󹪝guration 󹪝le 3 to be
used with corresponding SOP 󹪞ag 3.
Set SOPCon󹪝gFile4_O 9190 defaults.sfg Set the name of con󹪝guration 󹪝le 4 to be
used with corresponding SOP 󹪞ag 4.
Set SOPCon󹪝gFile5_O 9191 defaults.sfg Set the name of con󹪝guration 󹪝le 5 to be
used with corresponding SOP 󹪞ag 5.
Set SOPCon󹪝gFile6_O 9192 defaults.sfg Set the name of con󹪝guration 󹪝le 6 to be
used with corresponding SOP 󹪞ag 6.
Parameter Assignment/Addressing
6.19 Options for Multiple Con󹪝guration Files
NXGPro+ Control Manual
172 Operating Manual, A5E50491925A