SIPOS SEVEN 2SA7 - Default Chapter; Table of Contents

Operation instructions
SIPOS SEVEN: PROFITRON, HiMod
Page 2 Y070.302/EN
Contents
Contents
Contents
1 General information ������������������������ 4
1.1 Safety information ................................. 4
1.2 Transport and storage ........................... 5
1.3 Disposal and recycling .......................... 5
1.4 Notes to the operation instructions ........ 5
1.4.1 Warnings: Used symbols and
their meanings ....................................... 5
1.4.2 Scope .................................................... 6
1.5 Supplementary operation instructions ... 6
2 General information ������������������������ 7
2.1 Functional principle ............................... 7
2.2 Sub-assemblies ..................................... 8
2.3 Block diagram (electrical connections) .. 9
3 Assembly and connection ����������� 10
3.1 Mount to valve/gear ............................. 10
3.1.1 General assembly instructions
for all output shaft types ...................... 10
3.1.2 Output shaft type A .............................. 10
3.1.3 Mount stem protection tube ................. 11
3.2 Electrical connection ........................... 12
3.2.1 Connection with round plug ................. 12
3.2.2 Fieldbus connection ............................ 13
3.2.3 External potential conductor
connection ........................................... 13
3.3 Separate mounting .............................. 14
4 Instructions on operator
control and operation ������������������� 15
4.1 Crank handle, hand wheel .................. 15
4.2 Light emitting diodes (LED)
and display .......................................... 16
4.2.1 Overview of light emitting diodes ........ 16
4.2.6 Overview of status indication .............. 16
4.3 Actuator status indication .................... 18
4.4 Navigation through the menus ............ 23
4.4.1 Operation of the Drive Controller ....... 23
4.4.2 Explanation of symbols,
texts within menu ................................ 24
5 Start menu ��������������������������������������� 26
5.1 Control ................................................. 26
5.1.1 "LOCAL“ control mode:
‘Local' actuator operation .................... 27
5.1.2 ”REMOTE“ control:
........ 28
5.1.3 “OFF“ control:
................ 28
5.2 Language selection ............................. 29
5.3 Main menu overview ........................... 30
6 User management�������������������������� 31
6.1 General information ............................. 31
6.2 General procedure .............................. 31
6.3 Assign password to user level/
change password of a user level ......... 32
6.4 Enable user level ................................. 33
7 Commissioning ������������������������������ 34
7.1 General information ............................. 34
7.2 Additional gear .................................... 36
7.2.1 Select additional gear and
change parameters ............................. 37
7.2.2 Parameters and their values
in the ‘Additional gear’ menu ............... 38
7.3 Program closing direction, speeds,
cut-off modes and tripping torques ...... 40
7.3.1 Select the closing direction ................. 40
7.3.2 Program speeds/positioning times ...... 41
7.3.3 Program cut-off modes
and tripping torques/forces ................. 42
7.4 Adjust end positions for version
with signaling gear .............................. 45
7.4.1 General information ............................. 45
7.4.2 Signaling gear ratio ............................. 47
7.4.3 Procedure for initial end position
adjustment ........................................... 48
7.4.4 Readjust end positions ........................ 53
7.4.5
Adjust mechanical position indicator ... 55
7.5 Adjust end positions for version with
"non-intrusive" position encoder .......... 56
7.5.1 New setting (initial setting) .................. 56
7.5.2 Readjust end positions ........................ 59
8 Parameters and possible
parameter values ��������������������������� 61
8.1 Parameter menu ................................. 61
8.2 Valve-specicparameters ................... 62
8.2.1 Change parameters in the
'Valve' menu ........................................ 62
8.2.2 Parameters and their values
in the ‘Valve’ menu .............................. 64
8.3 Control system parameters ................. 66
8.3.1 Overview of Control system menu ...... 66
8.3.2 Operation sequence: Changing
the parameters in the
'Control system' menu ......................... 67
8.3.3 Control system – Control mode ........... 67
8.3.4 Control system – Alternative
control mode ....................................... 69
8.3.5 Control system– Binary input .............. 70
8.3.6 MODE input ........................................ 70
8.3.7 Control system – Analog input AI1 ...... 71