SIPOS SEVEN 2SA7 - Page 3

Y070.302/EN Page 3
Operation instructions
SIPOS SEVEN: PROFITRON, HiMod
Contents
Contents
8.3.8 Control system – Analog input AI2 ...... 71
8.3.9 Control system – Binary outputs ......... 71
8.3.10 Control system – Analog output AO1 .. 73
8.3.11 Control system – Analog output AO2 .. 74
8.3.12 Control system – Fieldbus ................... 74
8.4 Safety related parameters ................... 77
8.4.1 EMERGENCY input ............................77
8.4.2 EMERGENCY speed ..........................77
8.4.3 EMERGENCY position ........................78
8.4.4 Fault control source ............................ 78
8.5 Software functions ............................... 78
8.5.1 Enabling software functions
and customer variants ......................... 79
8.5.2 Positioner ............................................ 80
8.5.3 Proportional move ............................... 81
8.5.4 Optional software functions ................. 82
8.6 Special parameters ............................. 83
8.6.1 Tag number ......................................... 84
8.6.2 Separate mounting .............................. 84
8.6.3 Intermediate contacts .......................... 84
8.6.4 Motor ................................................... 85
8.6.5 Maintenance intervals of valve ............ 86
8.6.6 Check maintenance ............................ 86
8.6.7 Close tightly ......................................... 87
8.6.8 Rise time ............................................. 87
8.6.9 DC brake ............................................. 87
8.6.10 Delay of Power Failure Message ........ 88
8.6.11 Torquemeasurementange ............... 88
8.6.12 Thresholds for detection
of wire break at analog outputs .......... 88
8.6.13 Test operation ...................................... 89
8.6.14 DC link voltage limitation ..................... 89
8.6.15 Runtime monitoring ............................. 90
8.6.16 End position speed .............................. 90
8.6.17 Autom. TL adapt. end position ............ 91
8.6.18 DCS acceptance time ......................... 92
9 System settings������������������������������ 93
9.1 Display ................................................ 93
9.1.1 Display orientation ............................... 93
9.1.2 Standby screen ................................... 94
9.1.3 Fast to local ......................................... 95
9.1.4 Set standby time ................................. 95
9.1.5 Activate Standby ................................. 95
9.2 Adjust real time clock .......................... 95
9.3 Activate, deactivate Bluetooth ............. 96
9.4 Remote control unit ............................. 96
10 Torque curve ����������������������������������� 98
10.1 General information ............................. 98
10.2 Record torque curve ............................ 99
10.3 Save torque curve on
USBashdrive ................................. 100
11 Observe ������������������������������������������ 101
11.1 Electronic name plate ........................ 101
11.1.1 Tag number ....................................... 101
11.1.2 Order number and equipment .......... 101
11.1.3 Serial number .................................... 101
11.1.4 Original serial number ....................... 101
11.1.5 Firmware version ............................... 102
11.2 Inputs and outputs (observe) ............ 102
11.2.1 Binary inputs ..................................... 102
11.2.2 Analog input and outputs .................. 102
11.2.3 Torque switch (2SQ7 only) ................ 102
11.2.4 Fieldbus communication ................... 102
11.3 Actuator status .................................. 103
11.4 Torque zero adjustment ..................... 104
12 Diagnosis (operating data
and maintenance limits) ������������� 105
12.1 Operation data actuator .................... 105
12.2 Valve maintenance limits ................... 106
12.3 Maintenance valve ............................ 106
13 Communication and
data exchange ������������������������������ 107
13.1 Remote control .................................. 107
13.2 COM-SIPOS PC parameterization
software ............................................. 107
13.3 USB port ............................................ 108
13.4 DataexchangeviaUSBashdrive ... 108
13.4.1Updatermware ................................ 109
13.4.2 Save parameters on
USBashdrive ................................. 109
13.4.3 Load parameters from
USBashdrive ................................. 109
13.4.4 Save torque curve ............................. 109
13.4.5 Clone actuator ................................... 110
14 Maintenance, inspection,
service ��������������������������������������������� 111
14.1 General information ............................111
14.2 Lubrication intervals and lubricants ... 112
14.3 Lubricant assignment and quantity ... 112
15 Spare parts ������������������������������������ 113
15.1 General information ........................... 113
15.2 Spare parts list .................................. 113
15.3 Exploded views ................................. 114
15.3.1 Gear unit 2SA7...- ............................. 114
15.3.2 Small part-turn gear unit 2SG7...- ..... 115
15.3.4 Small part-turn gear unit 2SQ7...- ..... 116
15.3.5 Electronics unit .................................. 117
Index �����������������������������������������������������118
EU Declaration of conformity/
Declaration of incorporation
in accordance with Machinery
Directive ������������������������������������ 123