SIPOS SEVEN 2SA7 - Index

Operation instructions
SIPOS SEVEN: PROFITRON, HiMod
Page 118 Y070.302/EN
16 Index
16
Index
A
Acceptance time. .................... 92
Access authorization. ................. 31
Activate Bluetooth. ................... 95
Activate standby. .................... 95
Actuator duplication. ................. 110
Actuator state. ...................... 18
Actuator status indication. ............. 18
Additional gear. ...................... 36
Additional gear parameter. ............. 38
Adjust position indicator. ............... 55
Adjust position indicator, mechanical. . . . . . 55
Adjust real time clock. . . . . . . . . . . . . . . . . . 95
Adjust signaling gear ratio. ............. 48
Analog inputs
Analog input AI1. ................... 71
Block diagram. ..................... 9
Assembly kit for separate mounting. ..... 14
Autom. TL adapt. end position. .......... 91
B
Behavior on loss of signal parameter. .... 78
Binary outputs
Signaling output 1 overview. .......... 71
Block diagram. ....................... 9
Bus termination PCB. ................. 13
C
Central wheel. . . . . . . . . . . . . . . . . . . . . 45, 49
Change/assign password. ............. 32
Changing the characteristic of a parameter. 62
Changing the numerical value of
a parameter. ...................... 63
Clone actuator. ..................... 110
Close tightly. ........................ 87
Code
Enable software functions. ........... 79
Enable user level. .................. 33
Commissioning. ............... 31, 34, 35
Access authorization. ............... 35
General information. ................ 34
Prerequisites. ..................... 34
Sequence of the measures. .......... 35
Communication and data exchange
COM-SIPOS PC parameterization
software. ........................ 107
Remote control. ................... 107
USB port, Bluetooth. ............... 108
COM-SIPOS. ...................... 107
COM-SIPOS PC parameterization
software. ........................ 107
Connection
Direct connection. .................. 12
Electronics and gear unit separated. . . . . 14
Fieldbus. ......................... 13
Mechanical connection. . . . . . . . . . . . . . . 10
Round plug. ....................... 12
Control mode
Alternative control system. ........... 69
Binary. ........................... 68
Control system. .................... 67
Fieldbus. ......................... 69
Internal. .......................... 69
Local. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
OFF. ............................ 28
Remote. . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Control system
Alternative control mode. ............ 69
Analog input AI2. ................ 71, 74
Analog output AO1. ................. 73
Binary control mode. ................ 68
Binary inputs. ..................... 70
Binary outputs. .................... 71
Change parameters. ................ 67
Control mode. ..................... 67
Fieldbus. ......................... 74
Fieldbus control mode. .............. 69
Functions. ........................ 66
Internal control mode. ............... 69
Menus. .......................... 66
Processcontrollerxedsetpoint. ...... 69
Control system – Control mode. ......... 67
Control system parameters. ............ 66
Crank handle
Danger of crushing. ..see Safety instructions
Operation. ........................ 15
Cut-off mode. .................... 40, 64
Cycle operation. ..................... 89
D
Data exchange. .................... 108
Deactivate Bluetooth. ............... 95
DC brake. .......................... 87
DC link voltage. ..................... 89
DC link voltage limitation. .............. 89
DCS acceptance time. ................ 92
DCS parameters. .................... 66
Dead band. ......................... 80
Degrees. ...............see Signaling gear
Index