SIPOS SEVEN 2SA7 - Page 119

Y070.302/EN Page 119
Operation instructions
SIPOS SEVEN: PROFITRON, HiMod
16
Index
16 Index
Diagnosis
Maintenance valve. ................ 106
Operation data actuator. ............ 105
Valve. .......................... 106
Valve maintenance limits. ........... 106
Diodes. ............................ 16
Display. ............................ 16
Language. ........................ 29
Rotate. . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Standby screen. ................... 94
Display operation data. ............... 105
Display orientation. ................... 93
System settings. ................... 93
Disposal. ............................ 5
Drive Controller. ..................... 23
Drive Controller operation. ............. 23
E
Electrical connection
Connection with round plug. .......... 12
Direct connection. .................. 12
Fieldbus connection. ................ 13
Electronic name plate
Firmware version. ................. 102
Observing. ....................... 101
Order number and equipment. ....... 101
Original serial number. ............. 101
Serial number. .................... 101
Tag number. ..................... 101
EMERG.. .......................... 41
EMERGENCY input. .................. 77
EMERGENCY speed. ................. 77
Enable
Software functions. ................. 79
User level. ........................ 33
Enable customer variants. ............. 79
Enable/disable motor operation. ......... 70
Enable motor operation. ............ 66, 70
Enable software functions. ............. 79
Enable user level. .................... 33
End position adaptation. ............... 91
End position adjustment. .............. 91
End position adjustment for version
with non-intrusive position encoder. .... 56
with signaling gear. ................. 45
End position range. . . . . . . . . . . . . . . . . . . . 65
End position speed. .................. 90
Equal percentage. ................... 80
Explanation of display symbols. ......... 16
Exploded views. .................... 114
External analog speed setpoint. ..see Options
External potential conductor. ........... 13
F
Fast opening. ....................... 80
Fast to local. ........................ 95
Fast to LOCAL. ...................... 95
Fault signals. ....................... 18
Fieldbus. .......................... 107
Firmware version. ................... 102
Freely adjustable positioning times.
..........................see Options
Functional principle. ................... 7
H
Hand wheel. ........................ 15
HART. ......................... 76, 103
Heater. ................ see Motor heating
I
Indication
Display. .......................... 16
LEDs. ........................... 16
Standby. ......................... 94
Valve position. ..................... 55
Inspection. ........................ 111
Interlock. .........see DCS acceptance time
Interlock LOCAL/REMOTE. ............ 70
Intermediate contact. ................. 84
L
LoadparametersfromUSBashdrive. .. 109
Local operation. ..................... 27
Loss of signal, behavior. ............... 78
Lubricant assignment. ............... 112
Lubricant quantities. ................. 112
Lubrication intervals and lubricants. ..... 112
M
Main menu. ......................... 30
Maintenance, inspection, service. ...... 111
Maintenance intervals of valve
Motor operation hours. .............. 86
Switching cycles. ................... 86
Torque cut-offs. .................... 86
Maintenance valve. . . . . . . . . . . . . . . . . . . 106
Mechanical position indicator. . . . . . . . . . . . 55
Menu
Control system. .................... 66
Diagnosis. ....................... 105
Observing. ....................... 101
Parameter. . . . . . . . . . . . . . . . . . . . . . . . . 61
Control system. .................. 66
Safety. ......................... 77
Software functions. ............... 78
Special parameters. ............... 83
Valve. .......................... 62