SIPOS SEVEN 2SA7 - Page 120

Operation instructions
SIPOS SEVEN: PROFITRON, HiMod
Page 120 Y070.302/EN
16 Index
16
Index
Special parameters. ................ 83
System settings. ................... 93
MODBUS. ......................... 107
MODBUS operation instructions. ......... 6
Motor
Motor heating. ..................... 85
Motor protection. ................... 85
Motor warning. .................... 85
Motor heating. . . . . . . . . . . . . . . . . . . . . . . . 85
Motor protection. . . . . . . . . . . . . . . . . . . . . . 85
Motor protection on/off. ................ 85
Motor warning. ...................... 85
Mounting position. ................... 10
Display orientation. ................. 93
Remote control unit. ................ 96
Separate mounting. ................. 14
Separate mounting parameter. ........ 84
N
Name plate
Serial number. ..................... 82
Name plate, electronic. ............... 101
Navigation in the menu. ............... 23
Navigation through the menus. . . . . . . . . . . 23
Non-intrusive position encoder:
End position adjustment. ............. 56
General information. ................. 7
O
Observing. ........................ 101
Actuator status. ................... 103
Binary inputs. .................... 102
Binary outputs. ................... 102
Electronic name plate. . . . . . . . . . . . . . . 101
Fieldbus communication. ........... 102
Inputs and outputs. ................ 102
OFF. .............................. 27
Operate actuator. .................... 27
Operation data actuator. .............. 105
Options
Customer variants. ................. 79
Software function overview. .......... 82
Software functions. ................. 78
Original serial number. ............... 101
Outputange. ....................... 10
Output shaft. ..............see Spare parts
General assembly instructions. ........ 10
Type A. .......................... 10
Overview
Control system parameters. .......... 66
Observe menu. ................... 101
Optional software functions. .......... 82
Parameters and possible
parameter values. .................. 61
Safety relevant parameters. .......... 77
Special parameters. ................ 83
Overview of a menu. . . . . . . . . . . . . . . . . . . 24
P
Packaging. .......................... 5
Parameter
Change. . . . . . . . . . . . . . . . . . . . . 24, 64, 66
Control system. ................. 61, 66
Cut-off mode. ..................... 64
EMERGENCY input. ................ 77
EMERGENCY position. .............. 78
EMERGENCY speed. ............... 77
End position range. ................. 65
Intermediate contact. . . . . . . . . . . . . . . . . 84
Menu. ........................ 61, 66
Retry torque block. ................. 65
Select. ........................... 24
Speed. ........................... 64
Tripping torque. .................... 64
Valve. ........................... 61
Valve-specicparameters. ........... 62
Parameter menu. .................... 61
Parameters and possible parameter values. 61
Parameter selection. . . . . . . . . . . . . . . . . . . 24
Password. .........see Access authorization
Position. ............................ 9
Positioner. ................ refer to Options
Programming. ..................... 80
Positioner with proportional/split range
function. . . . . . . . . . . . . . . . . . . . see Options
Position indicator. ................. 51, 55
Positioning time adjustment. . . . . . . . . . . . . 41
Position recording – functional principle. .. 45
Position recording functional principle. .... 45
Potential conductor, external. ........... 13
Power failure message. ............... 88
Power module. ....................... 8
Process controller. ............see Options
PROFIBUS. ....................... 107
PROFIBUS DP. ...................... 74
PROFIBUS operation instructions. ........ 6
Program closing direction. ............. 40
Program cut-off modes and
tripping torques. ................ 40, 64
Program EMERGENCY position. ........ 78
Programming
CLOSE direction. .................. 40
Cut-off mode and tripping torque. ... 40, 42
Positioning time. ................... 41
Speed. ........................ 40, 41